Water in a rectangular, finished-concrete channel, n = 0.017 overflows a dam, as shown in the figure below, and goes into a stilling basin at which there is a hydraulic jump. If the channel is of width 15.5m, has a slope 0.00367, and carries 26.75 cumec, calculate the depth y at O and the depth y2 at the hydraulic jump. Figure 2: Jump 8m 0.00367 163 m

Water in a rectangular, finished-concrete channel, n = 0.017 overflows a dam, as shown in the figure below, and goes into a stilling basin at which there is a hydraulic jump. If the channel is of width 15.5m, has a slope 0.00367, and carries 26.75 cumec, calculate the depth y at O and the depth y2 at the hydraulic jump. Figure 2: Jump 8m 0.00367 163 m

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter8: Stresses In A Soil Mass

Section: Chapter Questions

Problem 8.14P

See similar textbooks

Similar questions

Only two decimal places ...
Water flows in a trapezoidal channel of 2 m width and side slope at 1:1. At upstream depth of 2 m, the Froude's Number is 3. If the water undergoes a hydraulic jump: Determine the Froude's number downstream of the jump. A 0.339 B 0.384 0.435 D 0.486
please answer upto two decimal places..
Fast plz
2. A rectangular channel has a base width of 7m and filled with water at a depth of 0.8m with a Froude Number of 5 before conducting a hydraulic jump. a. Find the Froude Number after the jump. b. What is the head lost due to the jump?
3(b). Water flows through a spillway and goes through a hydraulic jump shown in figure. Consider Flow rate Q=15m³/s per meter width of the channel and water depth Y₁ = 0.6m. Determine the downstream depth of the channel (Y2) after hydraulic jump occurs Energy Loss in the hydraulic jump Hydraulic Jump ↓ Y₁ = 0.6m L Y2 = ?
Help me solve
A horizontal bend in a 2.5 m diameter penstock goes through a change in direction of 40° as shown. The flow rate is 30 m³/s and the pressure in the pipe is 160 kPa. Determine the resultant hydraulic force acting on the bend, giving both its magnitude and direction. Neglect friction 40° -$2.5m PLAN VIEW Q=30m³/s
2 Hydraulics equations.
Water flows at a depth of y1=0.4ft in a concrete channel which is 10ft wide. The discharge per unit width is 10ft2/sec. Estimate the height of the hydraulic jump that will be formed if bed slope is equal to 0.0 and 0.15 respectively.
Example 5: Water flows with a velocity of 3m/s, and a depth of 3 m in a rectangular channel of 2 m. Then there is an upward step of 30 cm as shown below. Compute the depth of flow over the step. Vj=3 m/s y2=? I _Az=0.30 m Yı=3 m Datum (1) (2) 83
49. Well A has a piezometer reading of hi and Well B has a piezometer reading of h2. If h2 > hi: a. aquifer water is flowing from the Well A location towards the Well B location b. the direction of aquifer water flow cannot be determined c. the hydraulic gradient can be calculated using the head difference between the wells d. none of the above 50. Since 2007, what is the trend in the depth to the water level measured for the three USGS groundwater Texas stations examined in the homework assignment? a. no changes in the depth to the water have occurred b. the depth to the water has increased at all stations c. data was not available for all of the sites d. none of the above