Water in a main pipe at street level is at a gauge pressure of 140 kPa and is moving with negligible speed. A pipe connected to the main pipe is used to deliver water to a kitchen located on the fifth floor of a building, at h = 10 m above street level (see the figure below). What is the maximum possible speed with which the water can emerge from an open kitchen faucet?

Water in a main pipe at street level is at a gauge pressure of 140 kPa and is moving with negligible speed. A pipe connected to the main pipe is used to deliver water to a kitchen located on the fifth floor of a building, at h = 10 m above street level (see the figure below). What is the maximum possible speed with which the water can emerge from an open kitchen faucet?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Water flowing in a horizontal pipe is at a pressure of 1.40 x 10^5 Pa at a point where its cross…

Q: Figure 13 shows a steady flow of 40 kg / s of water at 20 ° C through a nozzle if D1 = 18 cm and D2…

Q: A pump delivers gasoline at 20 degrees Celsius and 12 (m^3)/h. At the inlet p1=100 kPa, z1=1 m, and…

A: given flow rate, Q=12m3/hr=123600m3/sinlet pressure, P1=100Kpadistance from datum at inlet,…

Q: You wash your roof with a water hose at a height of 8.0 m above the ground. You connect two garden…

A: Given- P1 = Atmospheric pressure = 1.01 x 105 Pa v1 = 6 m/s height from datum 2 to 1 = (h) = 8 m By…

Q: A woman is draining her fish tank by siphoning the water into an outdoor drain as shown in the…

A: The area of the base of the rectangular tank is A and the height is hTherefore, the volume of the…

Q: A 3.5-hp pump delivers 1140 lbf of ethylene glycol at 20°C in 12 seconds, against a head of 17 ft.…

A: Calculate the efficiency of the pump in %.

Q: Consider the following compressor that receives air at a constant rate of three cubic feet per…

Q: A pump is driven at 1800 RPM and delivers 12 GPM at 2000 psi. If the volumetric efficiency is 90%,…

Q: find the speed up with which it flows inside the hose.

Q: A small, high pressure water jet can be used for cutting various materials. A jet with a speed of…

A: For the solution refer below images.

Q: is desired to pass water from point 1 to point 3 to run a fluid engine, pressure p1= 700kpa and…

A: Power to be Transmitted = {density * flow * ( total required head)} / efficiency total head required…

Q: Water enters a fountain through a pipe with a cross-sectional area A₁ at a flowrate Q. The pressure…

A: Given:

Q: Water is flowing in the pipe shown in the figure below, with the 7.50-cm diameter at point 1…

Q: Problem 1. Air flows steadily in a duct from Section (1) to Section (2). At Section (1), the…

Q: Patm A water Tank C hi h2 As shown in the figure, at hi= 1.8 m, h2= 3.6 m positions, the water in…

Q: could you please help me calculate the maximum height of the jet , Hj in metres please

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

Water in a main pipe at street level is at a gauge pressure of 140 kPa and is moving with negligible speed. A pipe connected to the main pipe is
used to deliver water to a kitchen located on the fifth floor of a building, at h = 10 m above street level (see the figure below). What is the
maximum possible speed with which the water can emerge from an open kitchen faucet?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Given data

VIEW

Final solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

2. The figure shows a pipe reducing section that is bolted on to the end of a pipe. Water flows through the pipe and the reducing section and exits to the atmosphere. The diameter at station 1 is 20 cm and the diameter at station 2 is 15 cm. The velocity at station 1 is 5 m/s. water ①1 ② Figure for problem 2. (a) If h 22.5 cm, what is the force acting on the flange bolts? (b) Does Bernoulli's equation hold between stations 1 and 2? Explain. mercury
Water enters a cylindrical tank through two pipes at rates of 141 and 126 gal/min (see the figure below). If the level of the water in the tank remains constant, calculate the average velocity of the flow leaving the tank through an 8-in. inside-diameter pipe. Section (2) Q₂ = 141gal/min V 3= i D₂ = 8 in. Section (1) 2₁1 = 126gal/min Section (3) ft/s
Water flows from a hose that is connected to a main pipe that is at 400 kPa gauge pressure. A child places his thumb to cover most of the outlet of thehose, and makes a thin stream of water come out at high speed. If the hose is held up, how high could the jet go?
Water is ejected vertically from a pressurized tank as shown in Figure 2. The "3 atm" pressure value is an absolute pressure value. Figure 2 Calculate the gauge pressure at the bottom of the tank in kPa if the height in the tank is H = 4.1 m. calculate the velocity at the nozzle exit, in m/s, for H = 4.2 m. calculate the maximum height of the water jet from the nozzle, h, in m, for a velocity at the nozzle of 21.0 m/s Assume the density of water is 1000 kg/m3 and 1 atm = 1.01 x 105 Pa. Use g = 9.81 m/s2.
Water leaves a hose at a rate of 3.6-kg per 2.0-s with a speed of 19.3-m/s and is aimed at a toy car at the exact moment the car is hit the water slows down to 4.0-m/s (That is, we ignore any splashing back.) What is the force exerted by the water on the toy car?
H = (1) Water 12.0 Pump To double the outflow of a reservoir, a pump is added as shown in the Figure above. The head in the reservoir is H = 4 m, the pipe diameter is D = 0.4 m and the the total length of the pipe system system is L = 120 m. For reference, the density of water is given by Pwater = 998.2 kg/m³ and the acceleration due to gravity is given by g = 9.81 m/s². Please provide your answers to 2 significant figures. (a) Determine the head added by the pump to double the flow rate. Assume that the pipe friction remains constant at f = 0.022, independent of added pump. In addition, assume a sharp edge entrance at the reservoir with a local loss K₁ = 0.4. m (b) Determine the power of the pump. Power = 92500.0957588 L W D A correct answer is 12.0, which can be typed in as follows: A correct answer is 92500.0957588, which can be typed in as follows: (2)
Water is flowing in the pipe shown in the figure below, with the 8.20-cm diameter at point 1 tapering to 3.85 cm at point 2, located y = 11.5 cm below point 1. The water pressure at point 1 is 3.20 ✕ 104 Pa and decreases by 50% at point 2. Assume steady, ideal flow. What is the speed of the water at the following points? (a) point 1 m/s (b) point 2 m/s.
Water at 20 °C flows through the pump impeller shown in the figure below, where the inner and outer diameters of the impeller are 160 mm and 400 mm, respectively, and the width of the pump blades is 55 mm. Part A μA Blade Estimate the shaft power required to drive the pump at this operating condition. Express your answer to three significant figures and include appropriate units. W shaft = Value Pump impeller Units The impeller rotates at 3600 rpm. Under a particular operating condition, water enters in a direction normal to the inflow surface, the component of the outflow velocity normal to the outflow surface, Vr, is equal to 19 m/s, and the magnitude of the absolute velocity, V, at the outflow surface is 33 m/s. Outflow surface Inflow surface 4 160 mm ✓ 400 mm
A- Blood flow from the left ventricle into the aorta can be modeled as a reducing nozzle (Figure below). Model both the left ventricle and the aorta as a tube with diameter of 3.1 and 2.7 cm, respectively. The pressure in the left ventricle is 130 mmHg and the pressure in the aorta is 123 mmHg. Blood is ejected from the left ventricle at a speed of 120 cm/s. Calculate the difference in height between these two locations. V₂ Az = ? Aorta location 2 Left ventricle location 1
The water is flowing through a pipe having diameters 30 cm and 21 cm at sections land 2 respectively. The rate of flow through pipe is 40 litres/s. The section 1 is 7 m above datum and section 2 is 3 m above datum. If the pressure at section 1 is 37 N/cm? , find the following by neglecting losses: (ENTER ONLY THE VALUES BY REFERRING THE UNIT GIVEN IN BRACKETS) ) Area of cross section of section1 (unit in m?) = Area of cross section of section2 (unit in m?) = velocity at section 1 (unit in m/s) = velocity at section 2 (unit in m/s) = (ii) difference in datum head (Unit in m) = Pressure head at section 1 (Unit in m) = pressure head at section 2 (unit in m) =
The figure below shows a Venturi meter for measuring the water flow rate through a pipe. The cross-sectional area at Stations 1 and 2 is 0.01 m² and 0.006 m², respectively. The pressure difference between Stations 1 and 2 is measured using a U-tube manometer containing a liquid with a specific gravity (SG) of 1.4. The manometer head is h = 0.5 m. What is the volume flow rate Q through the pipe? Neglect viscous effects. The gravitational acceleration g is 9.81 m/s² and the density of water is 1000 kg/m³. (Note: The pressure difference is NOT simply given by PMgh, where PM is the density of the manometer liquid.) Q= 1. [0.014113976, 0.015599657 m³/s. 1 2 IT h
A reducing elbow is used to deflect water flow at a rate of 840 kg/min in a horizontal pipe upward 30.0while accelerating it, as shown in Fig. 1. The elbow discharges water into the atmosphere. The cross-sectional area of elbow is 113 cm2at the inlet and 700 mm2at the outlet. The elevation difference between the centers of the outlet and the inlet is 300 mm. The weight of the elbow and thewater in it is considered to be negligible. The density of water is 1000 kg/m3. Determine (a) the gage pressure at the center of the inlet of the elbow and (b) the anchoring force needed to hold the elbow in place.