Water flows through the 40-mm-diameter pipe assembly such that the velocity at A is 6 m/s and the pressure is 200 kPa The assembly and the water within it have a mass of 54 kg. Assume that the flow is steady and the water can be considered as an ideal fluid. -2 m- 40 mm 6 m/s 2 m Part A Determine the a component of force exerted at the support C, assuming there is no support resistance at A and B. Express your answer to three significant figures and include the appropriate units.

Water flows through the 40-mm-diameter pipe assembly such that the velocity at A is 6 m/s and the pressure is 200 kPa The assembly and the water within it have a mass of 54 kg. Assume that the flow is steady and the water can be considered as an ideal fluid. -2 m- 40 mm 6 m/s 2 m Part A Determine the a component of force exerted at the support C, assuming there is no support resistance at A and B. Express your answer to three significant figures and include the appropriate units.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. The motor delivers 3000 hp to the shaft at 1500 rev/min, and efficiently transmitted to gear B and C. Given the shaft diameters daB = 100 mm, dec = 80 mm and dco = 80 mm, determine the power removed by gear B and C if the maximum shear stress in the shafts is uniform; and (b) the angle of twist of end D lags behind the other end. Use G = 77 GPa for steel and assume that friction at the bearings at D is negligible. A TB To B D 0.4 m 0.6 m 0.35 m
Please answer it soon
Gate AB shown in the figure below closes a tank of water. the pressure gage at C shows a pressure of 10.8 kpa. The weight of the gate is negligible. there is an open manometer installed at the top of the tank. a.) Determine the manometer reading in mm. b.) Determine the total force acting on the gate. c.) Determine the force p required to open the gate.
Q4 (a) With the aid of diagram, define the Hydrostatic Pressure.
Solve it ASAP
12. Assuming smooth contact surfaces, determine the reactions of the cylinders at A, B, C and D. W = 500 N 2m 5.6 m W = 300 N 1m K. D
1. The rigid gate with 3m width is installed in order to control the water outflow as shown in the figure. The gate is hinged at point O and rests against a support at point B. Assuming that the weight of the gate as well as the friction at the hinge don't have significant effects, determine the following: Wate 4 m a. Determine forces (resultant forces). b. Locate the center of pressure for the hydrostatic forces (resultant forces). c. Required horizontal force, the gate closed. the magnitude of the hydrostatic Hing 3 m B A P in order to hold 2 m Atmosphere
fluid mechanics
Water enters and leaves a T-shaped piece of pipe located in the horizontal plane. (1) the relative pressure in the numbered section is 200 kPa and the cross-sectional average velocity is V1= 2 m/s. since the pipe diameters are the same in sections (2) and (3), determine the components of the force acting on the pipe. It will be assumed that there is no energy loss in the selected control volume.
SHOW COMPLETE SOLUTION
2. The pipe assembly is subjected to the force of F = (600i + 800j - 300k) N. Determine the moment of this force about Points A and B, specifically. 0.5 m B. 0.4 m 0.3 m 0.3 m
sF.ricylinder.rsh Tcy are the radius of shaft and inside radius of cylinder a P2.11 Consider a concentric shaft fixed axially and rotated inside K( cylinder.rsh.ľcy are the radius of shaft and inside_radius of cylinder respectively, with total length L. Let the rotational rate @ rad/s and applied torque be M .Using these parameters, a) Derive a theoretical relation for the viscosity u of the fluid between the shaft and cylinder. b) For a shaft of 8cm long, rotating at 1200 rev./min, with rsh = 2.00 cm and the measured torque is M viscosity? [µ = M(rcy=r sh)/(2nwr;,L)] %3D - 0.293 N.m. What is the fluid [µ=0.29 kg/m.s] rey:205 ( Coso 76 243.