water flows through a long copper tube (inside diameter 2.2 cm) with an average velocity of 2.13 m/s. The water is heated by steam condensing at 150oC on the outside of the tube. Water enters at 15o C and leaves at 60o C

water flows through a long copper tube (inside diameter 2.2 cm) with an average velocity of 2.13 m/s. The water is heated by steam condensing at 150oC on the outside of the tube. Water enters at 15o C and leaves at 60o C

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Flowing juice like 0.5kg / h enters the parallel-flow heat exchanger at 293 K and is heated by 400K water vapor (Cp = 1.76kJ / kgK), which is 2.5 kg / s. The exit temperature of the juice is 360 K, the area where heat transfer takes place Calculate the efficiency and heat transfer of the heat exchanger if it is 20 m2 and the overall heat transfer coefficient is 280W / m2K. (physical properties of fruit juice will be considered the same as water).
Need answer ASAP In a counter-current-flow tubular heat exchanger, a liquid food (milk),flowing in the inner pipe, is heated from 20 to 40°C. In theouter pipe the heating medium (water) cools from 90 to50°C. The overall heat-transfer coefficient based on the insidediameter is 2000 W/(m^2-°C). The inside diameter is 5 cm andlength of the heat exchanger is 10 m. The average specific heatof water is 4.181 kJ/(kg-°C). Calculate the mass flow rate ofwater in the outer pipe. Compare the amount of milk being heated to concurrent design.
I am reviewing methods of assessing systems in heat transfer. One of the method I have run across for looking at single pass heat exchangers is log mean temperature difference (LMTD). What is the advantage of using LMTD instead of the basic/arithmetic difference in temperatures?
A parallel flow heat exchanger is to be designed to heat 4535 kg/hr of water from 21°C to 43°C with the steam condensing at 121°C on the outside of the tubes. Tubes of 2.54 cm outside diameter and 2.286 cm inside diameter, 2.44m long, are available for use. Assuming that the average steam-side coefficient is 5675 W/m²-°C, and the thermal conductivity of the tube metal is 110.73 W/m²-°C, calculate the required number of tube per pass. Assume that the velocity of the water entering each tube is equal to 0.457 m/sec. a. 7 c. 9 b. 8 d. 10
310 m algunaourtsdi bayon bozu (A) In a food processing plant a brine solution is heated from 6°C to 12°C in a double pipe heat exchanger by water entering at 50°C and leaving at 40°C at the rate of 0.166kg/s. If the overall heat transfer coefficient is 850 W/(m².K), what heat exchanger area is required for (1) parallel flow heat exchanger and (2) counter flow heat exchanger. Discuss the results?. Take C₂ (for water)= 4.180 kJ/kg.K mbmeod (isolev si ma do liw novel
A one-shell pass and two-tube passes heat exchanger must transfer 300 kW to a solution with a specific heat of 3.28 kJ/kg-K and change its temperature from 60 C to 88 C. Steam is available at 120 C. The unit convective coefficient is 3200 W/m2-K for the inside and 8500 W/m2-K for the outside. The thermal conductivity for the tubes is 115 W/m-K and the tubes have 4 cm OD and 3 cm ID and are 3 m long. Determine the number of tubes required.
HERE ARE SOME APPLICATIONS OF SHEEL AND TUBE HEAT EXCHANGER: Power Generation HVAC Marine Applications Pulp and Paper Refrigeration Pharmaceuticals Air Processing and Compressor Cooling Metals and MiningPLEASE MAKE A EXPLANATION FOR THIS
Water must be heated from 15 to 50°C in a simple double-pipe heat exchanger at a rate of 3,500 kg/h. The water is flowing inside the inner tube with steam condensing at 110°C on the outside. The tube wall is so thin that the wall resistance may be neglected. Assume that the steam-film coefficient h_0 is 11 kW/m^2 °C. What is the length of the shortest heat exchanger that will heat the water to the desired temperature, considering an optimal diameter for the tube? Checking several table values, the following properties of water for this scenario are: p = 993 kg/m^3 k = 0.61 W/m °C \mu (viscosity) = 0.78 cP Cp = 4.19 J/g °C
he shell fluid,ethylene glycol, enters at 120oC and leaves at 60oCwitha flow rate of 4000 kg/h. Water flows in the tubes, entering at 35oCand leaving at85oC. The overall heat-transfer coefficient for this arrangement is 900W/m2·oC.The exchanger is a shell tube with two shell passes and two tube passes.Calculate the following: a) The water exit temperature if flow rate of glycol to the exchanger is reduced in half with the entrance temperatures of both fluids remaining the same and by how much is the heat-transfer rate reduced?; b) The percentage reduction of heat transfer if water-flow rate is reduced by 25percent,while the gas flowrate is maintained constant along with the fluid inlet temperatures. Assume that the overall heat-transfer coefficient remains the same; andc) The flow rate of water required andthe area of the heat exchanger;
SEMIFINAL PROJECT IN ME 3215 COMBUSTION ENGINEERING PROBLEM: Cooling water for 507 Horsepower Diesel Engine is to be cooled by using an intermediate cooling heat exchanger as follows. At Counterflow Heat exchanger. Jacket water in --- 60 °C Jacket water out 38 °C Tower water in 27 °C Tower water out - -54 °C To be done: Make the necessary valid assumptions and calculate the flow through heat exchanger for the following quantities: kg 1. Jacket water, in sec kg 2. Tower water, in sec to coling o NEAT EXCNANGER DESEL ENGE from cool