Water flows from a large reservoir as shown. The pipe is cast Iron, with inside diameter of 0.2 m. The flow rate is 0.14 m3 /sec, and the discharge is to atmospheric pressure. The mean temperature for the flow is 10℃. The system is insulated. Determine the gage pressure P1, required to produce the flow

Q: Water at 20 ºC is to be pumped through shown in the picture.  The inlet pipe to the pump is 0.06 m…

A: Length of the discharge line, L­DL = 60 m Length of the commercial steel pipe, LP = 8.5 m   The…

Q: Q2: It is required to pump cooling water from storage pond to a condenser in a process plant…

A:

Q: 3. As shown in the figure below, water at 20°C is flowing through the tubes A and B, then joining…

A: Temperature of water, T=20°C Diameter of tube A, DA=1 mm=1×10-3 m Maximum velocity through tube A,…

Q: Water flows in a pipeline composed of 75 mm and 150 mm pipe. Calculate the mean velocity in the 75…

A:

Q: 2 cfs of water is pumped through the 45° vertical pipe bend in the 6 inch diameter pipeline shown…

A: we'll use reynolds transport theorem

Q: Air is flowing isentropically through converging duct which is fed from a large reservoir where the…

A: Given infotemperature of air at the beginning of converging duct,T0=350kpressure  of air at the…

Q: 1. Water is flowing from the inlet to the exit. At the inlet the speed is 20m/s. Calculate (a) the…

A: Given,

Q: Water at 59 F flows through a straight section of a 6-in-ID cast-iron pipe with an average velocity…

A:

Q: On a circular pipe there are different diameters: diameter D1= 2 m changes into D2 = 1.5 D1. The…

A:

Q: 4.8. In a power plant, the inlet water has a velocity of 100 ft/s and an elevation of 80 ft above…

A:

Q: mooth inner surface for

A:

Q: Air enters a nozzle steadily at 2.21 kg/m and 30 m/s and leaves at 0.762 kg/m' and 180 m/s. If the…

A: Given   Density at inlet  of air(ρ 1) = 2.21 kg/m3 Velocity at inlet of nozzle (V1) = 30 m/s Inlet…

Q: Water at 20°C is flowing through a tube of diameter 0.010 m at a velocity of 0.10 m/s. a. Calculate…

A: Water is flowing through the tube at 200C. Tube diameter, D=0.010 m velocity of the water through…

Q: A centrifugal pump is tested at 1750 rpm using flow system with a layout. The water level in the…

A:

Q: g-0. flowing through nozzle ects the mer ube gage. Determine the value of h if the pressure at A is…

A: Given data: Specific gravity of Oil;SG=0.750PA=20 psi=137895 Pad=2.75 inches=0.069 m

Q: Water at 30°C is being pumped through a 30 m section of 19.49 cm. diameter steel pipe at a mass flow…

A: Given data: Length of the pipe = 30 m Diameter of pipe = 19.49 cm Mass flow rate = 0.07 kg/s Density…

Q: a. The entering temperature of a unit was measured at 200 F and the flow rate of the unit was 500…

A: Baseboard unit is the heating arrenegement used in heating homes at cold countries during winters.…

Q: A dilute aqueous slurry containing solids with a diameter of 20 micrometer and SG= 1.5 is fed to a…

A: The flow rate of the centrifuge is obtained from angular velocity, distance to liquid, distance to…

Q: The wastewater treatment process at a polymer plant consists of a longitudinal bio-remediation pond…

A:

Q: IVAN IVOU, Q3: Three pipes (A, B and C) are interconnected as shown in figure (3). Determine the…

A:

Q: For the system shown in Figure 7, water flows through the pump at a rate of 50 Liter/s. The…

A: Given,

Q: In a convergent-divergent nozzle where air, at 540 degrees F and 15200 torr enters and flows…

A: Note-Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question…

Q: the pump shown in the figure delivers water at 59 F at a rate of 550 gal/min. The inlet pipe has an…

A: We are given following data for the pump that delivers water:

Q: Assume frictionless flow in a long, horizontal, conical pipe. The diameter is 2.54 cm at one end and…

A: (a) Let us assume the origin of coordinate axis along center of pipe. Hence there is no change in y…

Q: Water is flowing through a 2.067-in D pipe with a velocity of 1 m/s. Calculate: (a) Mass flowrate…

A:

Q: Problem 1: Water flows steadily through the piping junction, entering section 1 at 0.0013 m³/s. The…

A:

Q: The flow through a 1.0 in diameter pipe is 5 GPM with a pressure drop of 10 PSI. What would the…

A: Given: diameter of pipe 1(d1)= 1 in diameter of pipe 2(d2)= 2 in pressure drop in pipe 1 (∆P1)=10…

Q: (a) Estimate the velocity and mass flow rate by B.E. (b) What is the force tending to tear the…

A:

Q: 1. s) Water in the old 15-in.-diameter concrete drainpipe runs full with a flow of 15 ft/s.…

A: Diameter of the pipe, D = 15 in. = 1.25 ft Length of the pipe, L = 12 ft The volumetric flow rate of…

Q: 2) Both ends of the nozzle with an inlet cross-sectional area of lx10-S ft² and an outlet cross-…

A: In fluid mechanics, Bernoulli's theorem is described as the total mechanical energy of the flowing…

Q: Water is flowing at an average velocity of 7 ft/s in a 6-in pipe. What is the pressure drop per unit…

A: