Water flows downwards in a vertical pipeline of gradually varying section from point 1 to point 2, which is 1.5m above point 1, at the rate of 0.9m^3/s. At section 1 the pipe diameter is 0.5m and pressure is 800 kPa. If pressure at section 2 is 600 kPa, determine the pipe diameter at that location. Neglect losses.

Q: Q4. A conical pipe has diameters at the two ends of 0.5 m and 1.5 m and is 15metres long. It is…

A:

Q: D;=10 cm D2=6 cm 2 h=8 cm Pc

A: Write the equation for the pressure at the manometric ends. P2=P1-ρggh+ρcgh Here, P2 is the pressure…

Q: Air at 68 degrees Celsius is being pumped through a pipe of internal diameter 6.4 inches. If the…

A:

Q: Question 4. The flowrate of the flow is 0,2 m³/s in a pipe placed on a horizontal plane. The pipe…

A: Let Fx =Force exerted by fluid on pipe in x direction  Fy =Force exerted by fluid on pipe in y…

Q: oil (0.88) ► oil (0.88) Hg (SG=13. 320mm-

A:

Q: Water flows through the pipe contraction shown in the figure below. For the given d=0.11 m…

A:

Q: 3m/s 100 mm 非 100 mm

A: To find the x and y component of the force in the cross section of the pipegiven diameter at the…

Q: horizontal 300-mm pipe contracts to a 150-mm diameter. If the flow is 0.127 m3/s of oil (s.g.=0.88)…

A: Given:Diameter of the bigger pipe, D=300 mmDiameter of the smaller pipe, d=150 mmFlow rate, Q=0.127…

Q: Determine the pump work of the oil piping system. The oil has kinematic viscosity of 0.0001 m²/s and…

A: Given:Kinematic viscosity of the oil, ν=0.0001 m2/sSpecific gravity of the oil, SGoil=0.79Pipe…

Q: 3. Water flows through a schedule-40 pipe that changes gradually in diameter from 6 in (154 mm) at…

A: Water flows through a schedule-40 pipe that changes gradually in diameter from d1= 6 in (0.154 m) at…

Q: 1a. Water flows into a tee fitting at a flow rate of 0.02 m3 /s. A pipe is connected to B. The…

A:

Q: Oil (Gs = 0.80) flows through pipe A at 200 li/s at elevation 20 m through a 200 mm diameter pipe…

A:

Q: Water flows from a pressurized tank, through a pipe of diameter D, exits from a nozzle of diameter…

A:

Q: 4. Brine (SG = 1.1, viscosity = 1.1cP) is pumped at a rate of 45 ft^3/min (ID = 2.5in) from large…

A: Specific gravity of Brine, SG=1.1Viscosity of brine, μ=1.1 cP=1.11488.1639lb/ft.sec=7.3916*10-4…

Q: Water enters a pipe of diameter 22 mm with a venturi meter with a throat diameter of 12 mm. At the…

A:

Q: d D

A: Note:- hete inclination angle for carriage is not given so, I directly find the Net force along the…

Q: 22/Water flows steadily through the nozzle shown in Figure No. (2) at flow rate Q= 0.06 (m³/s). The…

A: Since you have uploaded multiple question, as per the guidelines we will answer the first question…

Q: Given parameters D1=30 cm L1=300 m D2=20 cm L2=150 m D3=25 cm L3=200 m f1=0.018, f2=0.02, and…

A:

Q: 4. Determine the pressure required, in psi, in the pipe just ahead of the nozzle shown in the figure…

A: Given jet velocity v2= 75 fps diameter d1= 1 in  diameter d2 = 0.75 in

Q: A cast-iron pipe system consists of a 500-ft section of water pipe, after which the flow branches…

A: Applying bernoulli's equation,

Q: For the system shown below, calculate the vertical distance (in meters) between the surfaces of the…

A:

Q: Q2/: As shown in the figure, the Assumptions of the flow through the venturi is steady,…

A: (1) Draw the diagram of the venturi meter.

Q: Suppose it takes ½ hour to fill a 16 ft x 32 ft x 7 ft swimming pool from a 2.0 in. diameter pipe,…

A: Time required to fill the swimming pool, t=12hr=12*3600 seconds=1800 secVolume of the swimming pool,…

Q: Calculate the flow rate of the system by accepting the fluid passing through the reservoir-pipe…

A:

Q: Water flows at the rate of 5 ft3/s through an inclined pipe. At point A, where the diameter is 12…

A:

Q: Two pipes in a series have a flow rate of 50 L/s. The pipe upstream is 300 mm and reduced downstream…

A: Given Data Q=50 L/s D1=300 mm D2=150 mm

Q: Pm = 900 kg/m 2.5 m Water 0.08 m

A:

Q: Water with a constant density 62.4 lb/ft^3 is flowing at a rate of 50gal/min through a horizontal…

A:

Q: compressible fluid flows steadily in the entrance region of dius R = 75 mm. The flow rate is Q = 0.1…

A:

Q: VII. Suppose water is leaking from a tank through a circular hole of area An at it's bottom. When…

A:

Q: Determine the forces F_x and F_y necessary to hold the pipe stationary.

A: Determine the forces F_x and F_y

Q: Problem Consider a cylindrical pipe of length L and diameter D = 2R. The angle that the axis of the…

A: The suspicions of the situation are that the liquid is incompressible and Newtonian; the stream is…

Q: Flow takes place between three reservoirs. the volume flow rate out of reservoirs A and B is…

A: Given:Discharge, QA=0.15 m3/sQB=0.25 m3/sf=0.008

Q: The diameter of a pipe changes gradually from 75 mm at a point A, 6 m  above datum, to 150 mm at B,…

A:

Q: Two tanks A and B are connected by a pipe 30 m long. The first 21 m has a diameter of 75 mm and…

A: Given data as per question The total length of the pipe =30 m diameter of first 21 m length =75 mm…

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.