Please make sure the following things are done for this problem;• Draw a system diagram• Make a statement of any assumptions• Show all given properties• Write all appropriate formulas• Maintain units throughout workWater contained in a closed, rigid tank, initially saturated vapor at 200° C, iscooled to 100° C.Determine the initial and final pressures, each in bar.Sketch and locate the initial and final states on sketches of the p-v and T-vdiagrams

Given that Water contained ina closed rigidtank Initial saturated vapour at temperature = 200 °c…

Water contained in a closed, rigid tank, initially saturated vapor at 200° C, is cooled to 100° C. Determine the initial and final pressures, each in bar. Sketch and locate the initial and final states on sketches of the p-v and T-v diagrams

Water contained in a closed, rigid tank, initially saturated vapor at 200° C, is cooled to 100° C. Determine the initial and final pressures, each in bar. Sketch and locate the initial and final states on sketches of the p-v and T-v diagrams

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 2-kg saturated liquid Refrigerant-134a at 0. 40 MPa undergoes the following: Process 1-2:…

A: Given data: - The mass of saturated liquid Refrigerant-134a is m = 2 kg. The pressure of saturated…

Q: 2. Saturated liquid water at 250 kPa is contained in a piston-cylinder device as shown in the figure…

Q: A cylinder-piston assembly initially contains water at 3 MPa and 300°C. The water is cooled at…

Q: Ammonia contained in a closed, rigid tank is heated from an initial saturated vapor state at…

A: Given Temperature, T1 = 20°C T2 = 40°C Find Final pressure, P2

Q: A water storage tank contains liquid and vapour in equilibrium at 110oC. The distance from the…

Q: Consider the following table for Refrigerant-134a. Required: а) Complete the table and show all…

A: Given Data: The refrigerant used, R-134 a

Q: 1. A vessel of volume 0.01 m³ contains a mixture of saturated water and steam at 150°C. The mass of…

Q: For water with pressure of P=8MPa and specific volume v=0.023525 m3/kg, (2) Find the specific…

A: Introduction Using a steam table, we will determine the specific volume of saturated liquid at the…

Q: 3. Sulfur dioxide at a temperature of 204 °C occupies a volume of 0.3 m3 A. If the volume is…

A: Given Data: The initial temperature the of sulfur dioxide is, T1=204°C=204+273 K=477 K. The initial…

Q: 2) Water in a pressure cooker is observed to boil at 175°C. What is the absolute pressure in the…

Q: For water with pressure of P=8MPa and specific volume v=0.023525 m³/kg. (3) Find the specific volume…

A: Given data Pressure = 8 Mpa Specific volume = 0.023525 m3/kg Find the specific volume at saturated…

Q: On a T-V diagram sketch the constant specific volume through the reference state (state 0) T = 250C,…

A: given; draw T-V diagram for water at different temperature ?

Q: 3-4. In cach case, determine the requested property values and show the states on carefully-labeled…

A: Given Data ***As per our company policy we are supposed to do only three subpart if you need the…

Q: A piston-cylinder device contains an ideal gas of nitrogen. At the initial state, the volume is V₁=…

A: Qout = 2.80 kJ Cp = 1.039 kJ/kg.K

Q: What is the internal energy, u, in kJ/kg of refrigerant R22 at temperature T=-10°C. and specific…

Q: Using the tables for water, determine the specified property data at the indicated states. In each…

A: (a) From the steam table at P = 2 MPa, and T = 300 oC, At 2 MPa,Tsat=212.417 °CHence, At 2 MPa and…

Q: A piston-cylinder device contains an ideal gas of nitrogen. At the initial state, the volume is V₁=…

Q: Q3/ An ideal gas is changed from p1 = 1bar, v1= 10m³ to p2 =10 bar , v2 = 1m³, calculate Q & W for…

A: Write the given values using suitable variables. Here P1 signifies initial pressure, V1 signifies…

Q: Determine the volume for water vapor at 200 bar and 470 oc at 10kg, using (a) ideal gas equation (b)…

A: (a) By using the ideal gas equation the specific volume is PV=mRTV=mRTP=10×0.4615×74320000=0.171…

Q: Required intormation On the property diagrams indicated below, sketch (not to scale), with respect…

Q: Task 3 A 3 m tank contains air at 15 C and 400 kPa is connected through a valve to another tank…

A: Given Data Volume of tank 1 is :V1=3 m3 Temperature of air in tank 1 is : T1=15°C Pressure in tank…

Q: An ideal gas is changed from p1 = 1bar, v1= 10m3 to p2 =10 bar , v2 = 1m3 , calculate Q & W for the…

A: (a) Isothermal process in thermodynamics refers to the process in which energy transfer takes place…

Q: Q2. Determine the phase in a system consisting of water at the following conditions and sketch T-v…

Q: Saturated water vapor at 50°C has its pressure decreased to increase the volume by54.571% keeping…

Q: 5. A copper calorimeter can with mass 0.446 kg contains 0.0950 kg of ice. The system is initially at…

Q: . In a sturdy closed container with a volume of 0.3m ^ 3, there is a wet steam of 300 kPa in…

Q: For each of the following cases, determine the specifified properties and show the states on the…

Q: d. A rigid vessel of volume 1 m3 contains steam at 20 bar and 400°c. The vessel is cooled until the…

Q: Air in a rigid tank is at 200oC and 150 kPa. The air is cooled to a final equilibrium state of 60oC…

A: Given that, Initial temperature of air inside tank, Ti=200 °C,Pressure temperature of air inside…

Q: A piston-cylinder device contains an ideal gas of nitrogen. At the initial state, the volume is V1=…

Q: A piston-cylinder device containing 2kg of saturated H2O at 187 °C has initial specific volume of…

Q: Problem 5. A piston-cylinder assembly contains 0.15 kg of H2O in an initial state where the fluid is…

A: Given data as per question Mass of water contained = 0.15 kg Pressure maintained = 400 kpa Heat…

Q: 3.9 Determine the quality of steam in a vessel containing 3 kg of saturated vapor and 7 saturated…

Q: A sealed vessel with a volume of 200 m³ is heated by a heat source. At the beginning of the process…

A: Given: The initial volume, V1 = 200 m^3 The initial pressure, P1 = 120 bar The liquid fraction, xL =…

Concept explainers

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.

Question

Please make sure the following things are done for this problem;
• Draw a system diagram
• Make a statement of any assumptions
• Show all given properties
• Write all appropriate formulas
• Maintain units throughout work
Water contained in a closed, rigid tank, initially saturated vapor at 200° C, is
cooled to 100° C.
Determine the initial and final pressures, each in bar.
Sketch and locate the initial and final states on sketches of the p-v and T-v
diagrams

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Trending now

This is a popular solution!

Step by step

Solved in 6 steps with 40 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Please provide solution. Thanks!
Part b only asap Thanks
Thermodynamics: Please show me how to solve the following practice problems in step by step solution (Thank you so much!)
Draw a figure or FBD that will support the problem. Explain each step by step formula.
Thermodynamics Topic: Ideal Gas or Perfect Gas Solve completely in handwritten with given, req’d & sol’n Thank you!
Not Ai generated please show all steps
SHOW SOLUTION STEP BY STEP WITH UNITS. SUBJECT: THERMODYNAMICS TOPIC: PROCESSES OF GASES
Please show system sketches and related energy flows for all problems. 1.1 Determine the electrical power supplied to a boiler when the temperature of the entering water is 20 C and the exiting temperature is 89 C. The flow of the pressured water is 2 Kg/s. There is a negligible pressure drop through this boiler and it operates at a constant pressure of 3 bars. The specific heat is c = 4,370 J/(Kg K). There is a 1.5(105 ) W rate of heat loss from the boiler during this process to a surrounding at 293.2 k. Consider steady state conditions. 1.4 Calculate the mass flowrate of fuel (natural gas, CH4) required to heat the water flow to the conditions of problem 1.1 if the electrical heating device is replaced with a gas fired boiler. The high heating value (HHV) of the fuel is 50.02 MJ/kg. 1.5 Calculate the exergy destroyed in the process described by problem 1.4. The exergy of the fuel entering this process is 51.82 MJ/Kg. The dead state temperature is 293.2 K and pressure is 1 bar. The…
Problem 6 Suppose a process takes 1.0 mol of monoatomic ideal gas in a closed system from state 1 to state 2, then from state 2 to state 3, as shown in the diagram below. Specifically, the path from state 1 to state 2 is isobaric at pressure pi=101,000 N/m². Then, going from state 2 to state 3, pressure increases linearly with volume until reaching p3=185,000 N/m². The volumes are as follows: V1= 0.010 m², V2 = 0.026 m³, V3 = 0.038 m³. a) Calculate the change in internal energy for the overall process. b) Calculate the work done on the system for the overall process. c) Calculate heat into the system for the overall process. 3 P3 1 2 P1 V1 V2 V3 V (m³) p (N/m²)
can I get simple answer for that question please with clear solution .
Please show system sketches and related energy flows for all problems. 1.a) Determine the electrical power supplied to a boiler when the temperature of the entering water is 20 C and the exiting temperature is 89 C. The flow of.the pressured water is 2 Kg/s. There is a negligible pressure drop through this boiler and it operates at a constant pressure of 3 bars. The specific heat is c = 4,370 J/(Kg K). There is a 1.5(105 ) W rate of heat loss from the boiler during this process to a surrounding at 293.2 k. Consider steady state conditions. 1.b) Calculate the total rate of entropy production 1.c) Calculate the total rate of exergy destruction (W). Given the dead state temperature 293.2 K and pressure 1 bar.
Suppose that you have designed a portable compressed-air supply system, as shown in the figure below,for filling scuba tanks and for driving pneumatics tools in garages and factories.The system consists of an electric motor, an air compressor, an air tank, a regulator and a pressure-reliefsafety valve.The regulator contains a pressure sensor connected to a power switch. The motor is switched on whenthe tank pressure drops bellow a fixed value and off at a slightly higher pressure. The pressure-reliefvalve is set to open at a higher pressure than the regulator motor off-pressure.Explosion of the tank is clearly a dangerous hazard. Three events are assumed to possibly lead to a tankexplosion:1. an internal tank defect such as poor welding2. an external cause such as a plant vehicle colliding with the tank3. Excess pressure in the tank. The excess pressure can occur only if both the control unit and thepressure-relief valve fail:The pressure sensor might fail to shut oof the motor because…