Water at four-degree Celsius flows through a pipe that has a conical shape and is sloping downward; has a height difference of 20 meters. The cross section at the bottom is one-half that at the top. If the speed and pressure of water at the top are I m/s and Pa, what is the nressure at the bottom (20 meters below the torn?

Q: Water is flowing into a frustum of a conical vessel 2 m high at 100liters per minute. The vessel has…

A: To determine the height of water when the water surface is rising at 25.72 mm/min.

Q: Q1. Water, assumed frictionless, flows from a large tank and exits through a vertical, constant…

A:

Q: The jet hits the point surface that is 12 meters. Pressure = 49.05 kPa Cv = 0.97   What is the…

A:

Q: 11. A tank 3.66m has its ends vertical, top and bottom horizontal, 1.82m high. The top and the…

A: Given: Required to find:  the time necessary to lower the water surface to 1.22m

Q: A water pipe runs vertically through a tall building, with a flow rate of 0.2 m³/s. The diameter of…

A:

Q: A pump draws water from a 20 cm diam suction pipe and discharges through a 15 cm diam pipe in which…

A: Pump efficiency is generally the ratio of water power output from the pump to the shaft power input…

Q: Oil flows through a small standard 25m  diameter orificce under a head of 5.4 m at the rate of…

A:

Q: The pressures at the ends of 605m long horizontal pipe flow are 350 kPa and 270 kPa. The pressure at…

A: The values given in the question are as follows length of the pipe(L)=605 m Pressure at upstream end…

Q: A 90° elbow in a horizontal pipe is used to direct water flow upward at a rate m of 34 kg/s. The…

A:

Q: Water is flowing at 0.020 m'/s at steady-state through a reducing 90-degree bend in the horizontal…

A: given data Q=0.02m3/secd1=0.05m and…

Q: Problem 2 Water at 60F ( 62.36 lb/ft³ and 7.536 * 104 lb/ft s) is flowing steadily in a 2-in-…

A: D = 2 in  Q = 0.2 cfs L = 200 ft

Q: Question 1 A vertical circular gate in a tunnel 8 m. in diameter has oil (0.80) on one side and air…

A: Solve letter A only Given- diameter d=8 m,air pressure P=40 kPa,oil height=12 m, Hydrostatic force=?

Q: The water is flowing through a taper pipe of length 250m having diameters 750mm at the upper end and…

A:

Q: Water is flowing at the rate of 4.7 cu.m./min. through a 150mm-dia. pipe which slopes downward such…

A:

Q: Problem 2 Water at 60F ( 62.36 lb/ft and 7.536 * 104 lb/ft s) is flowing steadily in a 2-in-…

A: Flow rate (Q) = 0.2 ft3/sLength of pipe (L) = 200 ftDiameter of pipe (D) = 2 in = 2/12 ftDensity of…

Q: A pump draws water from a 20 cm diam suction pipe and discharges through a 15 cm diam pipe in which…

A: Given,

Q: b) Water flowing in a 3000m length cast iron pipe with velocity of 1.5m/sec is closed at its outlet…

A: Given that: Length of pipe, l = 3000m                   Velocity of flow, v = 1.5 m/s…

Q: 3) Water is moving with a velocity of 5.0 m/s through a pipe with a cross-sectional area of 4.0 cm?.…

A:

Q: A 1.2m diameter open vessel, 2m high is filled with oil s.g = 0.85 at a depth of 1.6m and rotated at…

A:

Q: A pipe carrying sea water (SG = 1.03) reduces its diameter from 30cm at point 1 to 10cm at point 2.…

A:

Q: A flat circular plate, 1.25 m diameter is immersed in sewage water (density 1200 kg/m³) such that…

A: Given data : Diameter of circular plate = 1.25 m Density = 1200 kg/m3 Greatest depth = 1.50 m Latest…

Q: Q7) Water flows from a large reservoir to a smaller one through a 5-cm diameter smooth piping system…

A: The given data is shown below: Diameter=5cmDynamic viscosity=0.001307 Pas

Q: Water at 25° is flowing between A and B through a steel pipe 30 centimeters in diameter and a length…

A:

Q: Assuming steady flow, determine the velocity of the flow through the narrowest region and the…

A: Given:- Diameter at the top of venturi section = 15cm             Diameter at the narrowest point of…

Q: A pipe carrying water tapers from cross section 0.5 m² at A to 0.2 m² at B. The average velocity at…

A: Cross sectional area = 0.5 m2 ar A and 0.2 m2 at B.The average velocity at A = 2 m/s and Pressure =…

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?