Water at 20°C flows through an inclined 8-cm-diameter pipe. At sections A and B, pA = 196 kPa, VA = 3.5 m/s ZA = 26.5 m, while pB = 280 kPa, and zB = 10.1 m. What is the head loss for this flow? in meters If the Darcy Friction Factor is 0.02 for this pipe, what is the length of this pipe from A to B?

Water at 20°C flows through an inclined 8-cm-diameter pipe. At sections A and B, pA = 196 kPa, VA = 3.5 m/s ZA = 26.5 m, while pB = 280 kPa, and zB = 10.1 m. What is the head loss for this flow? in meters If the Darcy Friction Factor is 0.02 for this pipe, what is the length of this pipe from A to B?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

This is a fluid machine question. Water reservoir is pumped over a hill through a pipe 450 mm in diameter and a pressure of 98.08 kPa is maintained in the summit water discharge is 30 m above the reservoir. The quantity pumped is 0.50 m3/s. rrictional losses in the discharge and suction pipe of the pump is equivalent to 1.5 m head loss. The speed of the pump is 800 rpm, what amount of energy must be furnished by the pump in kW?
. water at 20°C is to be pumped from reservoir 1 to 2 in a 6-in-diameter asphalted cast iron pipe at V = 6 ft/s. With 80 percent pump efficiency, the required power is 4.10 hp. What is he proper pipe length to match these conditions? Under the given flow condition, water properties are:p=1.94 slug/ft³ and u = 2.09E - 5 slug/ (ft s). For asphalted cast iron, e = 0.0004ft. 20 ft Pump
A vertical pipe in the form of a cone has a diameter of 45 cm at the top and 92 cm at the bottom and is 18.3 m long. The head loss is 3 m in either direction when the velocity at the top is 9.15 m/s and the pressure head there is 1.98 m of water. Find the pressure head at the bottom when the flow is (a) downward (b) upward. Draw the diagram.
Q.8 Venturimeter is installed in a pipe of diameter 40 mm. If the throat diameter of venturimeter is 20 mm and the pressure difference between the pipe and throat section is found to be 120 kPa. Then neglecting the frictional losses, the water velocity in main pipe is (m/s) A В 3 C 4 D 8
Water at 20°C fl ows by gravity through a smooth pipe fromone reservoir to a lower one. The elevation difference is 60 m.The pipe is 360 m long, with a diameter of 12 cm. Calculatethe expected flow rate in m3/h. Neglect minor losses.
I need the answer as soon as possible
B10
5
Hurry up plz
An oil with density of 900 kg/m3 and ? = 0.0002 m2/s flows upward through a 10 m long pipe segment inclined at 40° with the horizontal. The pressures at the upstream and downstream end of the pipe are 350 kPa and 250 kPa, respectively. The diameter of the pipe is 60 mm. Assume the flow is laminar. 1. The head loss along the pipe segment 2. Velocity of flow 3. Reynold’s number
water at 20°C is pumped through a smooth 12-cm-diameter pipe 10km long, at a flow rate of 75 m3/h. The inlet is fed by a pump at an absolutepressure of 2.4 MPa.The exit is at standard atmospheric pressure (101 kPa) and is 200 mhigher.Calculate the frictional head loss Hf and compare it to the velocity head of the flow.B) A gate valve is used to control flow in the above system. What is the headloss due to the addition of the valve?What is the total head loss in the new system?state any assumptions made. for the value fully open k=0.17, 3/4 open k=0.9, 1/2 open k=4.5 and 1/4 open k=24
Kerosene (SG=0.80) flows through the pump in the figure below at 65 liters per second. Head losses between 1 and 2 are 2 meters, and the pump delivers 6 kW to the flow. What should be the mercury manometer reading h be? (SGH9313.6) D, = 15 cm Pump 1.5 m D, =8 cm Mercury