Water at 15°C (p-1000 kg/m, u = 1.138 X 10-3 kg/m-s) is drained from a large reservoir using two horizontal plastic smooth pipes connected in series. The first pipe is 20 m long and has a 10-cm diameter, while the second pipe is 35 m long and has a 4-cm diameter. The water level in the reservoir is 18 m above the centerline of the pipe. The pipe entrance is sharp-edged (K = 0.5), and the contraction between the two pipes is sudden (K=0.46). Neglecting the effect of the kinetic energy correction factor, determine the discharge rate of water from the reservoir. Use either of Moody chart or Halaand relation.

Water at 15°C (p-1000 kg/m, u = 1.138 X 10-3 kg/m-s) is drained from a large reservoir using two horizontal plastic smooth pipes connected in series. The first pipe is 20 m long and has a 10-cm diameter, while the second pipe is 35 m long and has a 4-cm diameter. The water level in the reservoir is 18 m above the centerline of the pipe. The pipe entrance is sharp-edged (K = 0.5), and the contraction between the two pipes is sudden (K=0.46). Neglecting the effect of the kinetic energy correction factor, determine the discharge rate of water from the reservoir. Use either of Moody chart or Halaand relation.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water at 15°C is to be discharged from a reservoir at a rate of 18 L/s using two horizontal cast iron pipes connected in series and a pump between them. The first pipe is 20 m long and has a 6-cm diameter, while the second pipe is 35 m long and has a 3-cm diameter. The water level in the reservoir is 30 m above the centerline of the pipe. The pipe entrance is sharp-edged, and losses associated with the connection of the pump are negligible. Neglecting the effect of the kinetic energy correction factor, determine the required pumping head and the minimum pumping power to maintain the indicated flow rate.
A vented tanker is to be filled with fuel oil with p = 920 kg/m³ and μ = 0.045 kg/m-s from an underground reservoir using a L=25-m-long, 4-cm-diameter plastic hose with a slightly rounded entrance and two 90° smooth bends. The elevation difference between the oil level in the reservoir and the top of the tanker where the hose is discharged is 5 m. The capacity of the tanker is 18 m³ and the filling time is 30 min. Taking the kinetic energy correction factor at the hose discharge to be 1.05 and assuming an overall pump efficiency of 82 percent, determine the required power input to the pump. Tanker 18 m³ 4 cm- ✓ Lm Pump The required power input to the pump = KW
The drinking water to a village is supplied from a reservoir which is 475 m above and 25 km away from the village. The water is transported from the reservoir to an open-top storage tank in the village via a circular pipe with a diameter of 18 cm and a roughness of 0.15 mm. The population of the village is 1500 people. There are two valves (K=2) and five 90° elbows (K=1.5) along the pipe. Assuming that an average person in the village consumes 225 L/day, determine the power (kW) of the pump needed to transter the water from the reservoir to the storage tank. You can take the density and viscosity of water as 1000 kg/m and 0.001 kg/m s, respectively, and you can neglect the inlet and exit losses and the kinetic energy correction factor effects.
Water with density of 998 kg/m3 flows through an inclined pipe with diameterof 8 cm. At section A, pressure and elevation level are 175 kPa and 23.5 m,respectively. Meanwhile, pressure and elevation level at section B are 255 kPa,and 8.5 m, respectively. Determine the head loss and show direction of flowingwater.
A 1-in diameter cylinder 10 in long falls at 0.6 ft/s inside a tube of slightly larger diameter. A castor-oll film (u=6x10-3 lb-s/ft2) of constant thickness is between the cylinder and the tube. Determine the clearance between the cylinders in the tube in inches. (S.G for steel = 7.85)
A vented tanker is to be filled with fuel oil with ? = 920 kg/m3 and ? = 0.045 kg/m·s from an underground reservoir using a 25-m-long, 4-cm-diameter plastic hose with a slightly rounded entrance and two 90° smooth bends. The elevation difference between the oil level in the reservoir and the top of the tanker where the hose is discharged is 5 m. The capacity of the tanker is 18 m3 and the filling time is 30 min. Taking the kinetic energy correction factor at the hose discharge to be 1.05 and assuming an overall pump efficiency of 82 percent, determine the required power input to the pump.
Water at 20°C is withdrawn from a reservoir by means of a siphon, as shown in the figure. For d=10cm and D= 16cm, Determine: a) the minimum flow rate that can be achieved without cavitation occurring in the piping system, and b) the maximum elevation of the highest point in the piping system to prevent cavitation. c) Also, comment on the ways to increase the maximum elevation of the highest point in the piping system to prevent cavitation. (The saturation pressure of water at 20°C is 2.33 kPa)
Water at 25 deg C (998 kg/m 3 ) flows at 10 m 3 /s through a straight pipe of an ID of 1.38 m to 2 m-ID. Consider the level of the entrance and terminal bottom walls of the pipe equal, neglecting the effects of potential energy. In addition, the shaft work is zero. What is the Reynold's number. What kind of flow regime?
The geometrical head (height) of the turbine located in a hydraulic plant is 220m. The penstock for this turbine has a diameter of 53 cm and a total length of 375 m up to the turbine inlet. The continuous head loss coefficient in the pipe is 0.02. There are 3 elbows with a loss coefficient of 0.3 each and a valve with a loss coefficient of 6.8 in fully open condition on the penstock pipe. Turbine flow rate is 320 L/s, efficiency is 82% and speed is n= 750 rpm. (Psu= 998 kg/m³)wather v? P1 + as 29 P2 + az + z1 + hpompa.f = pg L V² + z2 + h¢arbing + hg,toplam_hg.sûrekli= f. 2g pg Wmil = hx.yeret =Kx hg,toplam= hx sürekli + hx,yerel Nsp Протра (gH)3/4 1/2 wWmil p1/2(gH)5/4 WB (DB Wmil,B _ PB (WB Nst = Wmil = pgHỳNtürbin , %3D %3D WA DA Wmil,a PA WA Wmil = prwv(V; - rw)(1 – cosß) a) Find the net drop of the turbine. b) Find the specific velocity of the turbine. c) Find the specific velocity of the turbine. 0,128 0,128 250,21 m 0,351 0,351 295,14 m 0,148 0,148 281,41 m 0,228 0,228 201,44 m…
The water surface in reservoir B is 12m higher than the surface of reservoir C. A 40-cm diameter, 0.7km long iron-cast pipe carries water at 20°C from B to C. Determine discharge for this pipe? Friction factor for iron-cast pipe, f-0.018. Ke-0.5 and Kd=1.0, where: Ke - entrance coefficient; Kd- discharge coefficient. O A. 0.232m3/sec O B. 360L/sec OC.0.360m3/sec O D.0.336m3/sec