Water at 10°C flows through the system shown in the figure below at 0.34 m/s. Energy loss in the 40-cm pipe is negligible. Energy loss in the 30-cm pipe is known to be 1.5V2. A mercury manometer indicates that the absolute pressure at the top of the 30-cm pipe is 749.5 mm Hg abs. The pressure of the surroundings is 101,330 Pa. Calculate the power input to the pump. p = 749.5 mm Hg Elevation = 10 m- D= 30 cm -Elevation = 6 m 40-cm diameter Water T = 10 °C Elevation = 2 m W = kW

Water at 10°C flows through the system shown in the figure below at 0.34 m/s. Energy loss in the 40-cm pipe is negligible. Energy loss in the 30-cm pipe is known to be 1.5V2. A mercury manometer indicates that the absolute pressure at the top of the 30-cm pipe is 749.5 mm Hg abs. The pressure of the surroundings is 101,330 Pa. Calculate the power input to the pump. p = 749.5 mm Hg Elevation = 10 m- D= 30 cm -Elevation = 6 m 40-cm diameter Water T = 10 °C Elevation = 2 m W = kW

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pipe set up is given as seen in the figure. The fluid is oil with a specific gravity of 850 kg/m³. The pressure at the exit is atmospheric pressure. The diameter at the entrance is 6.4 cm and the diameter at the exit is 2.2 cm. The volume rate of flow is given as 0.0315 m³/s and thegage pressure at the entrance is 250 kPa. Ignore weight of the fluid and the pipe. Determine the x-component of the force applied at the bolts at section 1. Assume that the atmospheric pressure is 1013 mb. 40° 2
Water flows through a Venturi meter, as shown in the figure. The pressures of the water at locations a and b in the pipe support columns of water that differ in height by L = 10 in. The atmospheric pressure is 14.7 lbf/in², the specific volume of water is 0.01604 ft3/lb, and the acceleration of gravity is g = 32.0 ft/s². Step 1 Patm = 14.7 lbf/in.² g= 32.0 ft/s² Determine the difference in pressure between points a and b, in lbf/in². Does the pressure increase or decrease from point a to point b? Water v = 0.01604 ft³/lb Save for Later Determine the difference in pressure between points a and b, in lbf/in². Pb-Pa = i lbf/in² 4 Attempts: 0 of 4 used Submit Answer
The 1m diameter tank is initially filled with gasoline. There is a 3.1 cm diameter orifice in the bottom. If the orifice is suddenly opened, estimate the time (minutes) for the fluid level to drop from 2m to 1.5 m. Use SG (gas) = 0.7, Cd = 0.66. answer in 2 decimal places.
While filling up your car with gasoline, you notice that it takes 3 minutes to dispense 55 liters of gasoline through the 2.5 cm diameter hose. What is the average speed, in m/s, of the gasoline inside the hose?
Let the pressure gradient in the pipe be 1500 Pa/m and the diameter of the pipe be 4.0 mm. What is the average speed through this pipe of 20∘C motor oil? What is the average speed through this pipe of 100∘C motor oil?
Water at 20°C flows through a 11.5-cm-diameter pipe that has a 180° vertical bend, as in the figure. The total length of pipe between flanges 1 and 2 is 75 cm. When the weight flow rate is 230 N/s, p1-165 kPa and p2-134 kPa. Neglect pipe weight. Determine the magnitude of the horizontal force balance that the flanges must withstand for the flow. The magnitude of the horizontal force F=-
A steam turbine carrying a full load of 46 MW uses 77.7 kg/s of steam. The turbine efficiency is 78%, and it exhausts steam at 26 mm Hg (absolute) with an enthalpy of 2310 kJ/kg. What are the temperature and pressure of the steam entering the turbine?(Note: One point for correct pair of temperature and pressure). Show the drawing
Air velocity in a duct is measured by a Pitot-static probe connected to a differential pressure gage. If the air is at 13.4 psia absolute and 70 degF and the reading of the differential pressure gage is 0.15 psi, determine the air velocity. ANSWER: 143 ft/s. The book provides the answer, but I'm stuck on what to do.
could you please help me calculate the verical force (in Newtons) on the door at time t=0
In the Venturi of the kerosene figure (density: = 0.85 ) seeps as ideal fluid. The area in section (1) is 24 cm2 while that of section (2) is 12 cm2. The average kerosene velocities in sections (1) and (2) are 4.5 m/s and 9 m/s, respectively. A manometer whose manometric fluid is mercury (y=133280 N/m3) is connected between sections (1) and (2) and indicates an unevenness "h". Find the unevenness ''h'' answer:0,206m
Please solve it quickly I am at the exam
0.95 m3/sec flow rate of water flows downwards in a pipe as shown in figure. If the pressures at points 1 and 2 are to be equal. Determine the diameter of the pipe at point 2.The velocity at point 1 is 6.5 m/sec and the diameter of pipe at point 1 is 330 mm. The height between point 1 and point 2 is 2.8 m?