waten tunnle

Q: Water was used in a manometer to measure pressure from a vessel. The difference in height between…

A: GIVEN DATA - DIFFERENCE IN HEIGHT h=2ft WE HAVE TO CALCULATE PRESSURE IN mm OF Hg

Q: How many balls of 30 mm diameter fit in a volume of 1.91 m^3

A: Given data: ● The total volume of space:  V = 1.91 m3 ● The diameter of the single ball: d = 30 mm =…

Q: m

A: The free-body diagram for the join D is as follows-The angles are as follows-

Q: What is the depth of the liquid from the free surface if the pressure at a point from the surface is…

A:

Q: holds 0.7ft3 of water. Filling up the tank requires how much water? a. 0.18 in3 b. 0.78 in3

A:

Q: What is the specific volume if the mass of an object is 120 lbs and the volume is 1250 ft3.

A:

Q: What would it be in celcius

A: From the result, the final temperature of the air in the tank is 277.3 K

Q: A kiloJoule/meter ( kJ/m) is ?

A: kj/m it is just showing energy grediant . distribution of energy or variation of energy along the…

Q: Pls i need answer asap. Fluid Mechanics: A piece of Ore weighing 2 N in air is found to weigh 1.216…

A: (a) Write the given data. W=2 NWsubmerged=1.216 Nγw=9800 N/m3

Q: Complete the following table for specific volume of water pressure specific volume (m³/kg) (bar) 80…

A: Specific volume of water is defined as the volume of the water per unit mass. It is expressed in the…

Q: Q3: The uniform beam has a mass of 50 kg per meter of length. Determine the reaction the supports.…

A: GIVEN:

Q: ight has a vo

A:

Q: PROBLEM 2. A structure shown in the figure weighs 3 kN/m each member supported by hinges at A and C.…

A:

Q: Consider a steady-flow Carnot cycle with water as the working fluid executed under the saturation…

A:

Q: How many balls of 70 mm diameter fit in a volume of 1.91 m^3

A: Given data Diameter of ball = 70 mm Total volume = 1.91 m^3 Brief introduction First determine…

Q: Draw the F.B.D. for the beam shown in fig and then find the reactions at A * ? 2 kN 4 kN/m L--x A 3…

A: The given beam is a cantilever beam having a few loads on it. A is a fixed end. So, it will contain…

Q: The uniform 100-kg I-beam is supported initially by its end rollers on the horizontal surface at A…

A:

Q: Question 19 A section of a rotating shaft is under an alternating bending moment of 70Nm and a…

A:

Q: Q. 1: A cast iron bracket subjected to bending has a cross-section of I-shape with unequal flanges…

A:

Q: PART A Using the graph to the right, what would Air Pressure be (mb) at an altitude of 10 km? What…

A: Given:The graph of altitude Vs pressure.The  axis of the graph is pressure and  axis of the graph is…

Q: Answer q1c. Qa was sent previusly if you need to refer to any calculations

A:

Q: building has the dimensions of 20 feet by 49 feet.   What is the area of the building in square…

A: Given dimension of the building Length = 49 ft Breadth = 20ft    To determine :the area of building…

Q: An engine has internal combustion volume of 6.31 liters. What is that volume in cubic inches?…

A: Given data volume(V) = 6.31 liters

Q: (a) In a refrigerating plant using R12 the vapour leaves the evaporator dry saturated at 1.826 bar…

A: solution provided in attachment. note : extra data is needed to get power in KW

Q: Q. 7: Two shafts of same material and same length are subjected to same torque. If the first shaft…

A: Given data: dh=34DH Need to compare the weight of two shafts.

Q: The volume of a 45’ container is 87.16 m3. The internal measures are: Length: 44’4” ft Height: 8’4”…

A: Volume of container, V=87.16m3 Length, L=44'4"=(44*12)+4=532" (inches) Height, H=8'4"=(8*12)+4=100"…

Q: Problem Solving: Input your final answer on the space provide. Note: Use three decimal places and no…

A: To find: The weight must be added inside to make the sphere neutrally buoyant. Given: The diameter…

Q: Q3: You have a truss which is shown below, two forces applying on it in B and C joints, which are…

A:

Q: (d) The brake engine efficiency (7,). (e) The indicated engine efficiency (7ind).

A: As you mentioned i gave answer of d). and e). For solution refer below images.

Q: 9. Water is heated by a 200 mm by 200 mm vertical flat plate which is maintained at 60°C. Find the…

A:

Q: om the given figure shown below, determine the centroidal moment of Inertia (Ixo and lyo) of the…

A: From the figure, we can conclude that all the values are in inches.

Q: Problem 24.16 It has been observed that the yield strength of the material of a component is…

A:

Q: 1. A reservoir contains 2.83 cubic meters of CO at 6895 kPa and 23.6 deg. Celsius. A cylindrical…

A: To find: The diameter of tank  Given data : The volume of CO in tank (Vco)=2.83 m3 The initial…

Q: Please answer with units every proceedure what is the volume (ft^3) occupied by water if has a…

A:

Q: Q. 6: A steel rod 20 mm in diameter, 400 mm long is co-axially enclosed in brass tube of 25 mm…

A:

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.