WĄ a GO lb WB = lol6 a 60 lb %3D B Find UA after A A 37° s ft down Moved the plane a) assume b) Take AK=O! no friction %3D

Q: Find the moment (Nm) caused by the force F = 239 N about point C if a = 24 mm and b = 34 mm. Round…

A:

Q: Hi, my question is in the picture.  This is a Dynamics question.

A: Given data as per questionAcceleration of the elevator = 5 ft/s2deacceleration of the elevator = 2…

Q: Specifically a dynamics problem. Question and diagram in pic below.

A:

Q: PROBLEMS in EQUILIBRIUM OF PARALLEL F.S. PROBLEM SP307 A honzontal beam 10 ΚN/m supported by a…

A: Given Data The UVL acting at A is: w=20 kN/m The UDL acting is: 10 kN/m The length of the UVL is: 6…

Q: can you help me to do the position analysis of this mechanism and find the mathemetical expressions…

A: Given:To find:Draw the position analysis and find the angle values.

Q: Hi, my question is in the picture.  This is a Dynamics question.

A:

Q: The pile P has a mass of 800 kg and is being driven into loose sand using the 300-kg hammer C which…

A:

Q: This disk has a radius of 2.7 meter and a mass of 80 kg. What is the mass moment of inertia about an…

A: The mass of disc is The radius of disc is

Q: Thank you for your answer, assuming that i have T4 and T4s and p3 and i am willing to find p4. Would…

A: This question is based on the concept of turbine and isentropic efficiency.

Q: Find mobility of given mechanisms through Gruebler's and Kutzbach's Equations

A: Kinematic Inversion as Follows:- Mechanism 1 Mechanism 2   Mechanism 3

Q: Specifically a dynamics problem. Question and diagram in pic below.

A: The equation for the magnitude of the velocity The equation of radial velocity is

Q: QUESTION 2 In Figure 2, the shaft is made of a solid A992 steel at section AB (rs = 25 mm),…

A:

Q: Determine the magnitude and coordinate direction angles of the resultant force. 0.75 m FAR = 250 N…

A: Given, FAC = 400 N FAB = 250 N

Q: A bullet of mass m has a velocity vo just before it strikes the target of mass M. (Figure 1) Figure…

A: The mass of the bullet is m The mass of the block is M. The velocity of a bullet is vo

Q: Specifically a dynamics problem. Question and diagram in pic below.

A:

Q: Specifically a dynamics problem. Question and diagram in pic below.

A: The automobile is originally at rest at s = 0. The speed of the automobile increases its speed as

Q: Find the moment (Nm) caused by the force F = 239 N about point O if a = 24 mm and b = 34 mm. Round…

A:

Q: Specifically a dynamics problem. Question and diagram in pic below.

A:

Q: m L O a L/2 8.0 g k

A: Given,

Q: Need to find degree of freedom by using gruebler and kutzbach equations please.

A:

Q: Specifically a dynamics problem. Question and diagram in pic below.

A: Given data as per question Speed of A = 90 ft/s Speed of B = 105 ft/s Taking horizontal and vertical…

Q: 6) An object falls a distance h from rest. If it travels 0.50h in the last 1.00 s, find (a) the time…

A: Given Datas=0.5hg=9.81 m/s2

Q: Give 3 examples of the Third law of motion citing which is the action and the reaction.

A: Example-1: When a force is applied on a body, the equal opposite reaction force is developed by that…

Q: Specifically a dynamics problem. Question and diagram in pic below.

A:

Q: I received an answer for my last question and I am still a bit confused. In the solution you said…

A: Hi thank you for reposting the question, in previous question I have assumed by mistake that in…

Q: -20kN 8. A steel bar ABCD 4 m long is subjected to force as shown in figure below. Find the…

A: Answer: The total elongation of the bar is 1.7507 mm.

Q: Specifically a dynamics problem. Question and diagram in pic below.

A: The car starts from rest at s = 0 and increases its speed at the tangential acceleration The final…

Q: When a slotted crank (r = (10 + 500ž) in mm, and 0 = n in radian, the angular velocity and angular…

A:

Q: Hi, please help me find the correct solution and answer to this problem. Our topic here is about…

A:

Q: Find degree of freedom for dump truck dump mechanism showed in picture.

A: For the given mechanism  To determine  degree of freedom

Q: A block of mass M is constrained by rollers to motion in the x direction. A small mass m is attached…

A:

Q: Specifically a dynamics problem. Question and diagram in pic below.

A: The radial component of velocity of point P can be calculated as follows

Strain energy

The term strain indicates the variation in an object's length, area, and volume when the object is subjected to an external force. The external force may be of normal, shear, moment, torque, etc. The strain in an object depends on the types of external force and cross-section of the object. Mathematically, the evaluation of strain can be obtained with the help of elastic constants.