VsI R2 Vi V2 R1 L2 3 m 30 152 2H 170V Io 4 0.6366HZ R3 90° R4 Vs2 50 502 110V 6 0 = 4 rad/s Current source 1 L) SA 0.6366H2 0° 0.6366HZ C1 L1 45° 0.5F 5H in

Q: Approximate solution time is 5 minutes. A transformer supplies power to a feeder that has five…

A:

Q: Using 24v AC source design a 24v unregulated power supply circuit that will power a 1kohms load with…

A: Given: C=480μFR=1kΩVm=24VRipple voltage=50 mVT=1ms

Q: sinco so l0d) ideal transformer M:05 Vi amplitnate is Sovi icoHz. Li=0.4H Lo=o.5H tind VR, in time…

A: The ideal transformer in the above figure is converted into the T- circuit model

Q: Draw FWR Vs=15Vrms Vrpp=.2v VDC=? R=5000hm F=60HZ C=?

A: Given, Vrms=15VRL=500ΩVrpp=0.2VSo,Vrrms=Vrpp2=0.22V,Vrrms=Vpp2⇒Vpp=2 VrmsSo, VDC=2Vppπ=22 Vrmsπ…

Q: Consider Two same size series connected PV modules,each with the specification as Po=100W, Voc=…

A:

Q: How do you realize a subtractor using full adder?

A: as per the guidelines we need to solve  only first question. we need to design full subtractor using…

Q: Current Transformer is used to step up the current of power system. Select one: True

A: Current transformer is a step down transformer. It always step down the current.

Q: converter topologies in pv system

A: It is asked to discuss about the converter topologies in PV system.

Q: A E₂ R2 R₁ F E E D₁ S с R3 E3 Equating E3 C Ec HH R₂

A: Anderson's bridge:- It is a type of AC bridge which is used to determine self inductance of…

Q: For given circuit below Adjuts the VGG voltage to have following Vas values and calculate the…

A: Given circuit is shown below. Given data is VDD=12V, RD=1kΩ, RG=560kΩ. For MOSFET input current is…

Q: ONO2. find diz= I2/I1 in the figore shown 2221 n.

A: In the question, depended and independent circuit are consist.  What is value of the current I2 /I1…

Q: Design a Bridge FWR to supply a load of (1002) with the waveform shown in figure from the main power…

A: Note: We are authorized to answer three subparts at a time since you have not mentioned which part…

Q: Find the load impedance that transfers maximum power to the load and determine the maximum power…

A:

Q: Q(1): For the figure shown below, use nodal analysis to find the value of Vo 2Vx 2/k A IkN Ikn IkQ…

A:

Q: Question: Using The Three Rules For Series Circuits And Ohms Law, Solve For The Missing Values

A: Considering a series circuit which will have 3 resistances of different values, let current flowing…

Q: Choose the supply voltage for a step down chopper circuit which drives the resistive load 4.80 with…

A:

Q: What do we connect in Series?

A:

Q: 50. A series resistance-capacitance (R-C) circuit is connected to 230-volt, 50 cycle AC source. The…

A:

Q: 44) When doing delta-to-wye conversions A) if the resistances are equal in one configuration, then…

A: From the delta star conversion formulas decide which statement is correct.

Q: Q6. Specification/Range of Power Supply:

A:

Q: The offset voltage describes the dc component of a dc electrical signal. True False

A: Offset voltage (Vos) is defined as the voltage that must be applied to the input to cause the output…

Q: sera s: -. Bhe retis tonce of a sm langth of wire is un n. Detiad the resifance of an 8m longth of…

A: Dear,as per company guidelines we can answer only one question at a time, kindly post other…

Q: hown below, By using Nodal Analysis, find R,

A:

Q: Represent a circuit diagram that applies an alternating voltage of 250 V over a 5-0 having access to…

A: According to the given data, Circuit will be HereVs=VL=250VAccording to transformation ratio of…

Q: 1. Determine the current of each line and the neutral current and measure the total power supplied…

A: Given: 3 phase 4 wire star connected load ZR= 950 ohm resister in series with 3 H inductor ZB = 1950…

Q: Explain what RLC circuits do and how they work including transformers, where applicable.

A: It is asked to explain what RLC circuits do and how RLC circuits can work including transformers…

Q: The actual impedance of a load is 30 OHM. The per-unit impedance of the load is 0.5 pu when Base…

A:

Q: Hot-spot effect in PV strings is advantage to PV efficiency. Select one: a. True. b. False.

A: Hot-spot effect in PV strings

Q: Design and Simulation of an Inverter Type Single-Phase Arc Welding Machine

A: We have to Design and Simulation of an  Inverter Type Single-Phase Arc Welding Machineusing…

Q: Q10. In a transformer modeling, the value of the voltage referred to primary side is O [N/N; 1*V, O…

A: The solution can be achieved a follows.

Q: What is load regulation?

A:

Q: Q5/B: Explain delta-star connection of 3 ph transformers. What its advantages and disadvantages?

A: ∆-Y connection of 3-phase transformer: In a three-phase transformer with a delta-star connection,…

Q: The purpose of using oil in transformers is due to:

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: H.W: The following data relates to the basic AC bridge under balance condition Zl = 80 260°; Z2 =…

A: Given, AC bridge under balanced condition Z1=80∠60°Z2=180∠70°Z3=20∠40°

Q: Q2:Buck-Boost Converter or Step Up Step Down Converter has following CCt prove if the Vo Match the…

A: Given buck-boost converter circuit: The input voltage Vs is connected to the chopper (CH). The…

Q: Q6. Using Nodal Analysis, Calculate V1 and Current I. [V1 12A RE4N )7A

A:

Q: With proper diagram show that, circular convolution is one kind of linier convolution.

A: Linear Convolution:

Q: Approximate solution time is 5 minutes. A transformer supplies power to a feeder that has five…

A: Given a transformer supplies power to a feeder that has a 5 consumers. Daily maximum demands for…

Nodal Analysis

In the analysis of any electric circuit, nodal analysis is the method of determining the potential difference or voltage between different nodes in an electric circuit. A node is a point where two or more branches connect each other. In the nodal analysis, the voltages are determined in the terms of branch currents. The nodal analysis is also known as the node voltage method or branch current method. The nodal analysis method is one of the several applications of Kirchhoff's Current Law (KCL).