VR Line impedance Mi M1 Transformer Vs VT M3 M: M2 Line impedance neutral Line impedance M3 Figure 2: Distribution lines equivalent circuit. Figure 1: Low voltage lines exiting the distribution transformer center. In the given circuit, low voltage lines are seen coming out of a distribution transformer whose Low Voltage side is star connected. R (R = 0) phase for M1 line, S (@S = 120) phase for M2 line andT (øT = -120) phase is used for M3 line. The impedances of the loads at the end of the lines are (100 + j25) N and the impedances of the lines (1 + j) N. • Find line currents

VR Line impedance Mi M1 Transformer Vs VT M3 M: M2 Line impedance neutral Line impedance M3 Figure 2: Distribution lines equivalent circuit. Figure 1: Low voltage lines exiting the distribution transformer center. In the given circuit, low voltage lines are seen coming out of a distribution transformer whose Low Voltage side is star connected. R (R = 0) phase for M1 line, S (@S = 120) phase for M2 line andT (øT = -120) phase is used for M3 line. The impedances of the loads at the end of the lines are (100 + j25) N and the impedances of the lines (1 + j) N. • Find line currents

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What size primary conductor can be used for a three-phase, 480V transformer, where the primary overcurrent protection is sized at 175A? a. 1/0 AWG b.2/0 AWG OC. 3/0 AWG d.4/0 AWG
Two transformers are to be operated in parallel such that they share load in proportion to their KVA rating. The rating of the first transformer is 500 kVA and its pu leakage impedance is 0.05 pu. If the rating of second transformer is 250 kVA, then its pu leakage impedance is A 0.20 B 0.10 C 0.05 D 0.025
A conventional phase transformer given in the figure will be connected as an autotransformer in two different ways. Each For a connection, find the input and output powers by drawing the connection. a) Connection of 1220 / 220V autotransformer b) 1000 / 1220V autotransformer connection
TRUE or FALSE: Delta-wye configuration of three-phase transformer is best suited for step-up applications.
3. Machines 1 & 2 --- 100 MVA, 18 kV, X"=X2=0.3, Xo= 0.07 pu Machine 2 Xn = .1 pu Transformers ------ 100 MVA, 20-345Y kV X=0.1 pu Line 2-3 z1=1+j120 ohm zo= 2+j300 ohm Machine 1 Kary 1 T₁ 2 2013 FY-Y (3) T₂ TO A A. Develop a base table with a 100 MVA, 345kV base in the Line. Machine 2 Kroooy
Two single-phase transformers, having equal turns ratio, in parallel supply a secondary load of 1,000 A at 0.8 pf lagging. For each transformer the secondary emf on open circuit is 3,300 V and their total leakage impedances referred to secondary are (0.10 + j0.20) ohms and (0.05 + j0.040) ohm, respectively. Determine the output current on each transformer.
3) The resistances and leakage reactances of a 40-kVA 60-Hz 7.97-kV-V:240-V single-phase distribution transformer are R₁ = 41.6 22 R₂ = 37.2 m2 X = 42.1 Ω _ X = 39.8 mΩ where subscript 1 denotes the 7.97-kV winding and subscript 2 denotes the 240-V winding. Each quantity is referred to its own side of the transformer. a. Draw the equivalent circuit referred to (1) the high- and (11) the low-voltage sides. Label the impedances numerically. b. Consider the transformer to deliver its rated kVA to a load on the low-voltage side with 240 V across the load. (1) Find the high-side terminal voltage for a load power factor of 0.87 power factor lagging. (ii) Find the high-side terminal voltage for a load power factor of 0.87 power factor leading.
Q14) please need correct answer fast!!
Solved Problems: Single-Phase Transformers Problem 1 A 19.2 KVA, 19200/480-V, 60 Hz, single-phase transformer is tested with the following results: Open-circuit test (measured from Low-voltage side ) Voc = 480 V Ioc = 1.25 A Poc = 160W Short-circuit test (measured from high-voltage side ) Vsc = 1150V Isc = 1.00A Psc = 190W a- Calculate and Sketch the equivalent circuit of this transformer when referred to its low-voltage side. The transformer is now loaded: 15 KW load, 0.9 lagging PF, and a load voltage of 450 V. b- Find the voltage on the high-voltage side of the transformer. c- Find the voltage regulation of this transformer.
Q/A single-phase transformer with a capacity of 100 kVA and a voltage of 2000/400 and the equivalent circuit elements are: As follows R1 = 0.1 02 x1 = 0.2 2 R2 = 0.25 2 X2 = 0.75 2 RO = 500 XO = 150 Q and feeds a load of 90 kVA at a voltage of 2000 volts and a power factor of 8.0 in delay. Calculate voltage and current Primary Royl ww JX eql
What would be the total single phase 120kVA capacity that could be used with the transformers size of 1.5 kVA?
In the following power system, the base voltage in region 2 is 13.8 kV. The transformer reactance is in per unit. The transmission line and load impedance are in Ohms. 2 3 = 300 Zjoad 13,2 kV Z, = 10 + j100 S MVA ri-ssdi w 10 MVAnizU 13.24 - 132Y kV X, = 0.1 138Y - 69A kV X12 = 0.08 Determine the following a. The base complex power in regions 1, 2, and 3 b. Base voltage in regions 1, 2, and 3 c. Base impedance in regions 1, 2 and 3 d. Base current in regions 1, 2 and 3 e. Actual impedance of transformers 1 and 2.