VIll. From the truss shown, Draw the Influence line of Members BC and BF. Also, Determine the maximum stress on these members due to a uniform load of 50 kN/m 3 m long moving along the line of the bottom chord.

Q: 2. Construct the influence line diagram for the bar force in member HK of the truss shown. Determine…

A: Data givenFind: Maximum positive and negative bar forces at member HK due to loading conditions (a)…

Q: the truss shown in Figure. Determine the force member at AB. 400 kN 800 kN 6 m 3 m 3 m C 6 m 6 m 200…

A:

Q: Solve by joint method. Should correct

A: Given Data Determine the forces in each member using Method of Joints.

Q: compute reaction A 2. determine the force carried by member BC due to 50kN applied load determine…

A:

Q: Draw the influence lines for members DI and IJ of the truss depicted in the figure below assuming…

A:

Q: Solve the given truss. Determine the following: 1. Axial force on DI.  2. Axial force on KO.  3.…

A: Given data,

Q: 26. The truss structure with a pin support at A and a roller support at C. The truss is subjected to…

A:

Q: Determine the magnitude of force in member BD

A: Find the magnitude of force in member BD

Q: Determine the resultant force at pins A, C, and E. Also, determine the forces on pin D. y 80 kN/m 40…

A: in the given beam the transverse loading on the beam both shear force and bending moment my…

Q: 1.2 m 25° 40° 2 kN D 1.2 m 1.2 m E

A:

Q: The beam is pin supported at A and roller supported at B. It carries two concentrated loads P = 4 kN…

A:

Q: Load A 3.5 m 45° 45% Load B 45° 45 3.5 m 45 B.

A: Abbreviation used  C = Compression member T = Tension member FAB = force in member AB (similarly for…

Q: In the rigid frame shown in figure, a central concentrated load is acting on "BC". Find slopes e, 0…

A:

Q: 2 m 5 kN B Determine the force in member BC, in kN. 3 m 10 kN 5 m

A:

Q: Compute the bar forces in the lettered bars of the truss shown. P P P P P Ja 45% 45° a

A:

Q: Find the member forces and reactions for the truss with loading shown.

A: Given -  To find -  Find the member forces and reactions for the truss with loading shown.

Q: AM IS SUPPORTED BY A PIN AT A AND WIRES P ON THE BEAM CAUSES THE END C TO BE DISP WARD, DETERMINE…

A:

Q: 700 N 800 N 566 N 60° 45 60° 45 30° 3 m 3 m А, 3 502 N Е, %3D 764 N (а)

A:

Q: 4 m 4 m 2 m 60 kN 120 kN

A:

Q: THE RIGID BEAM IS SUPPORTED BY A PIN AT A AND WIRES BD AND CE. IF THE LOAD P ON THE BEAM CAUSES THE…

A:

Q: Analyze the beam loaded and supported as shown: Ans.: A 40 kN Ans: 2 m 6m B Hinge (a) Determine the…

A: Given: Required: Maximum shear and bending moment

Q: Determine the magnitude of the pin force at B. 0 0.43 m 0.61 m 125 N-m B 0.43 m 0.43 m

A: To find out the magnitude of the pin force at  B.

Q: 10 ft 12 ft D E 60 k Pins at B and D 16 ft Fixed at A Pinned at F F - 8 ft A Prob 5) Solve for the…

A:

Q: 6. Determine the force components at B and C, as they act upon member AC. 2.25 m 1,200 N BA DF (DF =…

A:

Q: 250 kN 116 kN 71 kN 208 kN 61 m 54 m 54 ml

A: GIVEN GIRDER SYSTEM

Q: 2P 1.5P P 1.5P 2P , hinge B. D 15m 7m 7m 4@10m = 40m

A:

Q: 2 The section of a crane hook is a rectangle 6 cm x 4 cm. The centre of curvature of the section is…

A:

Q: Determine the maximum value of the bar forces in member FG, BG and BC for the truss shown due to the…

A:

Q: Determine the normal stress at A and B in member CD. Pins C and D are at the centroid of the T…

A: Calculating the total area of T-Cross section A: A=(7*1.5)+(6*1)   =16.5 in2

Q: Construct the influence line for the shear at point C of the am: 4 m 10 m

A: To draw ILD for shear at point C

Q: Determine the horizontal reaction at the hinged support. Determine the stress of member AB.…

A: We are given  Wind load = 1.44 kpa Spacing of truss = 3 m We get uniform loading on cantilevered…

Q: Determine the force (kN) at member BC and BD

A:

Q: Solve a and c

A: Given data : Shear force (V)=15 KNWidth (B)=40 mmDepth (D)=140 mm

Q: Determine the force in members EF and Gl of the C E K 80 kN A truss shown 5 m SOLUTION F H…

A:

Q: The beam is subjected to an internal moment of M = 140 kN.m. Determine the bending stress developed…

A:

Q: PROBLEM 4 Determine the force in member DF. 10 KN A 14 kN E B D F H 6 m G 2 m 14 2 m 2 m 2 m

A: Given:- To find:- Force in member DF

Q: The axial load in (kN) in the member PQ for the arrangement below is 2m 160 kN 2m beam 2m

A:

Influence Lines

The graphs that show the variation of a function at a specific point on a beam or truss due to a unit load placed at any point along the structure are known as influence lines in engineering. Some common functions that are studied with influence lines are shear, moment, and deflection. In designing beams and trusses, it is important to use influence lines in structures where loads would move along their span such as bridges, crane rails, conveyor belts, floor girders, etc. The influence lines help to study where a load will create the maximum effect for any of the functions.