View Policies Current Attempt in Progress Water flows over the spillway shown in the figure below. If the velocity is uniform at sections (1) and (2) and viscous effects are negligible, determine the flowrate per unit width of the spillway. 4.8 m Q= (1) 2.8 m m³/s 0.4 m

Q: 20 40 t. 20 40 30 40 20 to 30

A: Gross area of the column =area of concrete + area of reinforcementGross area of the first column…

Q: Give other methods of determining the horizontal distance between two points.

A:

Q: III-3 BASIC STANDARDS IN TECHNICAL DRAWING III-3-1 Formats These are. on which are executed the…

A: To fill the blanks in the given question.

Q: -3 R3 - 10 10 Find the coordinates of the centroid 3.

A: To determine the coordinates of the centroid of the given object.   The geometry of the given object…

Q: 3. Given two Orthographic views of an object, construct an Auxiliary view of the indicated ( —P)…

A:

Q: Pb. Classify trees on the basis of Strength and Structure. Provide a short description in chart…

A: Trees can be classified into two types based on strength : 1 - Endogeneous trees 2 - Exogeneous…

Q: Write the units used by English systems to specify small areas?

A: Solution: In the English system, areas are basically given in square feet or square yards. For…

Q: Determine the ỹ coordinate. y b. = ky? a

A:

Q: Draw the 3 Principal Views of the object (given unit in mm, convert it to cm) 51 35 15 25 53 73 20…

A: 3D view of the object is provided. We have to draw three principal views of the object.  Three…

Q: For any engineering example discuss with drawing the Bathtub Curve

A: The bath tub curve is generally used in reliability engineering.   This curve signifies the…

Q: Give the coordinates for the following autocad drawing

A: The points are named as below

Q: 1⁄6 yard +3⁄8 yard

A:

Q: 12. The ability to magnify details in a drawing or reduce the drawing to see it in its entirety is a…

A: Generally in AUTOCAD zooming can be directly done by using keyboard shortcuts like using the “+” key…

Q: Q1:A)Write the command to draw Figure below by using Auto CAD program (Relative Coordinate Method).…

A: question being asked here is to draw the above diagram using AUTO CAD program and also clearly…

Q: What is ponit of view? What is first point of view and third point of view.

A: The term  Point of view will be referred to who is telling or narrating the story. A story can be…

Q: hat about pin d?

A: We know that Forces acting at Joint D are shown in figure below Forces moving away from joints are…

Q: Q.3. Use Scale (1:1), for the front and side views shown draw the isometric projection: 50 30 R30 30…

A: To get the isometric projection from the given views. 1. Draw two lines perpendicular to each other…

Q: ex (x+1)² +c

A: Write all numerators above the common denominatorUse  to expand the expression.

Q: weétermine the yalue j = 2. Det ermine the Yalue & I with Respecd to centroidal X axis =

A: 1. Value of y¯ Let 1 & 2 be the rectangle and 3 & 4 be the triangle.y¯=∑ay∑a…

Q: revolve the objects:   1) top view 2) right side view 3) front view

A: As per the guidelines we are supposed to answer only 3 subparts. Kindly repost the question for…

Q: Subtract 8.46 from 25.3.   25.3- 8.46

A: Subtract 8.46 from 25.3.

Q: 38 O 18 22 66 102 The known: front projection, side projection Required: Draw the three projections…

A:

Q: Locate the centroid for the following areas :

A: Figure is as shown

Q: Q3: Draw the Full Sectional Front view and Top View of given object 70 50 10 45 430 70 15 10 88 40

A: The following figure shows the Full Sectional Front View of the object.

Q: Kindly include the free-body diagram too.

A: Solution: Given: Initial velocity u = 96 k,/hr u = 96×100060×60=36.67 m/s Final velocity: V = 0…

Q: Isometric drawing

A:

Open Channel Flow

Open channel flow is a branch of fluid mechanics. It deals with the flow of fluid in an open conduit or free surface. In an open channel flow, gravity induces the flow of water whose surface is open to the air. This flow is free-falling rather than confined in rigid body conduits. The open channel flow depends upon two parameters that are the cross-section of the conduit and the velocity profile. Practical examples of open channel flow are streams, rivers, canals, and other drainage systems.In open channel flow, the cross-sectional area of at least one of the sides is exposed to air, and the surface of water faces atmospheric pressure. This flow is also known as free gravity flow. The cross-sectional area of the conduit can be either man-made or a natural channel. For instance, the flow in rivers and streams are natural conduits, and the flow in a canal and sanitary systems are man-made or engineered channels.