Vcc=+12VRc1k2Rg470k2.BC107VcV8Figure 3: Practical Fixed Bias Transistor Circuit2. Measure the DC voltages Vc and VB using digital multi-meters. Determinethe quiescent base current, collector current, and collector- emitter voltage.3. Measure the transistor current gain.4. Calculate the expected values of IBQ, Ico, and VCEQ. Use the value of Bdetermined in step 3 above. Assume that VBE = 0.7 theoretically. Tabulateyou results as shown in Table 1.

Solution :- Apply Kirchoff's voltage law in above question in the input side :- VCC - IBRB -VBE =…

Vec=+12V RC 1k2 R 470k2 . вс107 Vc Ve Figure 3: Practical Fixed Bias Transistor Circuit Measure the DC voltages Vc and VB using digital multi-meters. Dete the quiescent base current, collector current, and collector- emitter vo Measure the transistor current gain. Calculate the expected values of IBQ, Icq, and VCEQ. Use the value of %3D determined in step 3 above. Assume that VBE = 0.7 theoretically. Ta you results as shown in Table 1.

Vec=+12V RC 1k2 R 470k2 . вс107 Vc Ve Figure 3: Practical Fixed Bias Transistor Circuit Measure the DC voltages Vc and VB using digital multi-meters. Dete the quiescent base current, collector current, and collector- emitter vo Measure the transistor current gain. Calculate the expected values of IBQ, Icq, and VCEQ. Use the value of %3D determined in step 3 above. Assume that VBE = 0.7 theoretically. Ta you results as shown in Table 1.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

2- Illustrate the following: A. Define Biasing ?I B. Write the three types of biasing circuit in Transistors and mention the main difference among them?
d) What is the difference between npn and pnp transistor? e) Draw the energy level diagrams of semiconductor, insulator and conductor. rding to physical laws f) Show and explain the amplification in AC domain.
Give a short summary of below transistor configurations. 1. Base Bias2. Emitter Bias
Just need 1d and 1e answered.
Qa: A transistor dissipates 50W in an ambient temperature of 60°C, the thermal resistances are 0-0.5 °CW¹, 8ca-4 °CW. Determine the junction temperature without a heat sink. Determine the thermal resistance of the heat sink to avoid the junction temperature exceeding 180°C. )
QUESTION 4 For an n-channel Junction Field-Effect Transistor (JFET), the gate-source cut-off voltage, VGS(OFF), is -4 V and the drain saturation current, Ipss is 50 mA. The drain current ID, is 12 mA. Determine the gate-to-source voltage, Vos, of the JFET.
State and explain the relation of drain current versus gate to source voltage for an MOSFET.
i need the answer quickly
1. The collector-base voltage of a Si transistor is a. None of these b. zero c. 0.7 volts d. 0.3 volts 2. The current gain of a common-emitter transistor is the ratio of the a. base current to collector current b. collector current to emitter current c. collector current to base current d. Emitter current to collector current 3. A zener diode shunt regulator uses the zener connected a. in series with the load b. in series with RS c. across RS d. across the load 4. If the transistor is to operate in the saturation region, the base-emitter and the base-collector terminal has to bea. both forward-biased b. both reversed-biased c. reversed-biased and forward-biased respectively d. forward-biased and reversed-biased respectively 5. The base-emitter of the transistor operating in the active region is usually a. operating in the breakdown region b. reverse-biased c. forward-biased d. non-conducting
(R₁ = 10k2, Rs = 30kQQ, RG = 100kQ,Vm = 0.8 a) Determine operating point of the circuit. Verify your operation mode assumption. b) Draw small signal equivalent circuit. c) Calculate Rin - d) Calculate Ro. . e) Determine small signal voltage gain
4. For the circuit shown in Figure, determine IC and VCB. Assume the transistor to be of Germanium.
Example 8:-