There are 11 vehicles observed in a 500 m section of a highway. The average time headway is 3 seconds.What is the value of the space mean speed in kph? There are 11 vehicles observed in a 500 m section of ahighway. The average time headway is 3 seconds.What is the value of the space mean speed in kph?A63.82 kph54.54 kphC71.24 kphD 42.57 kph

Answered: value of the space mean speed in kph?

Engineering

Civil Engineering

value of the space mean speed in kph?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A brass rod is 185 cm long and 1.6 cm in diameter. What force in kN must be applied to each end of t...

A: What force in kN must be applied to each end of the rod to prevent it from contraction

Q: for the figure shown, determine the reaction at B in kN

Q: Analyze the frame shown and draw the shear, moment and axial diagram. 12KN/m of horizontal length d

A: Calculate the reaction at the support , ∑Fy=0Rb+Rd=12×2+5+2Rb+Rd=108 kN ...

Q: Determine the mass of the heaviest uniform cylinder that can be supported in the position shown with...

A: Stress in cable BC =σBC = 50Mpa Cross sectional area of BC = 100mm2 It has been asked in the quest...

Q: A marksman fires a bullet to a target. Three seconds later, he heard the bullet hits the target. If ...

Q: A 10 m thick clay layer with single drainage layer undergoes a settlement of 22 mm in 3 years. If th...

Q: 1. A watershed has four rain gage stations. The annual rainfall depths recorded at three stations ar...

Q: The force that will balance the resultant force is called equilibrant. It has the following characte...

A: Ans is (b)

Q: 60. If the loss of prestress is excessive resulting in ten cracks, which method shc used?

Q: Built-up column 10 m long consists of W350x90 with two 12 mm thick plates welded to form a box secti...

Q: The yearly precipitation in California has normal distribution. Calculate the value of the 50 year a...

Q: Car A experienced engine failure the moment it enters a 2-km highway that has a constant grade of 4 ...

Q: 17 KN/m 6 KN/m + 1m 3 m 4m 1m

A: Given The value of uniformly varying load is 6KN/m And the value of Uniformly distributing load = ...

Q: A 10 m thick clay layer with single drainage layer undergoes a settlement of 22 mm in 3 years. If th...

Q: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that dị 3...

Q: A carpenter wishes to construct a ladder with nine rungs whose lengths decreases from 24 inches at t...

Q: Each gate of a lock is 5m high and is supported by two hinges placed on the top and bottom of the ga...

Q: A blow count N = 5 was obtained at a certain depth of a clayey soil deposit. From the given table es...

Q: Determine the mass of the heaviest uniform cylinder that can be supported in the position shown with...

Q: Problem 3: A bracket of negligible weight shown in the figure below is loaded a force of 13.34 kN. F...

Q: Evaluate the resisting capacity against axial load due to skin friction on the following conditions.

Q: WHAT IS THE DIFFERENCE IN SOLVING OR GETTING THE ANALYSIS OF A FRAME USING PORTAL METHOD AND CANTILE...

A: Portal method and cantilever method Both the methods are approximate methods of analysing multistor...

Q: What are the magnitudes of axial forces in the members I, II, and III, respectively?

A: To find: Magnitude of axial forces

Q: The diameter and depth of cylindrical tank are 9m and 4m respectively. This tank contains brimful of...

A: As the temperature is increased the liquid will expand(decrease in unit weight). However the weight ...

Q: Calculate angular frequency of a cantilever beam of span 2.5 m and subjected to a point load of 1500...

Q: Calculate the moment (positive if counterclockwise, negative if clockwise) of the 370-N force on the...

Q: A cantilever truss carries a concentrated load P as shown in the figure below: e = tan (3/4) C V P W...

Q: 4. An igloo or Eskimo hut is built in the form of a hemispherical shell with an inside diameter of 1...

A: Given Data- Hemispherical shell igloo/eskimoInside diameter=12 ftuniform thickness=2 ftweight=40 lb ...

Q: A constant force F is applied for 3 s to change the particle's velocity from v1 to v2. Determine the...

Q: The perpendicular offset of the PT of a simple curve is 120.20m. If the angle of intersection is 50֯...

Q: A floor is supported by 75mm x 200mm wooden joists spaced @ 400 mm on centers with an effective span...

Q: Compound axial member ABC has a uniform diameter of d = 2.1 in. Segment (1) is an aluminum [E1 = 10,...

Q: (2) Estimate the SDI for the following filtered wastewater samples. If the water is to be treated wi...

A: The test time in minutes, and the volume filtered in ml is given. The formula for silt density index...

Q: . How many sealants are there used depending upon their suitability in a given situation?

A: To find: Number of sealants used to stable

Q: eights was pressed into soft clay in a borehole. The torque was applied and gradually increased to 1...

A: Using relation :s=TπD2H2+D36

Q: Problem II. A proposed elevated tank for a certain community has a diameter of 72 inches and a heigh...

Q: 4) Determine the minimum path tree from zone 7 to all other zones.

Q: 0.1. Determine the components of reaction at support A and Reaction at support B. See Figure QI. PKa...

Q: for the asphaltic material, the strain-time relationship , determined as follows under a shear stres...

A: To find - Determine the constants of the model represented behavior.

Q: 2) Mr. X performs the laboratory test and determines that 12 mg/l of alum dose is required to treat ...

A: Step 1: Amount of alum required per day = 14x10^6 x 12 /1000x10000= 168 kg

Q: Sel 10 only: 1. Which one has low Si + Al elements, land Earth crust or oceanic Earth crust? 2. Whic...

A: 1) heavier minerals are found in lower parts of crust. But mineral like Al are not found in oceanic ...

Q: Q/Discuss the statement Why are there three types of failure in the compressive test of concrete?

A: The compression failure are defined in terms of the three well known failure modes: Yie...

Q: At a specified point on a highway, vehicles are known to arrive according to a Poisson process. Vehi...

Q: Given the laboratory results of the Atterberg Limit Test below: LIQUID LIMIT TEST NO. Cone Penetrati...

Q: A constant force F is applied for 3 s to change the particle's velocity from v1 to v2. Determine the...

A: Given - A constant force F is applied for 3s. v1 = 15m/s and v2 = 30 m/s To Find - The force F fo...

Q: Determine the pressure in a vessel of oil (specific gravity = 0.85) at a point 15.95 feet below the ...

Q: Q1. Determine the components of reaction at support A and Reaction at support B. See Figure QI. P Kn...

A: To find - The components of reaction at A and B. Since the value of P is not provided so we have to ...

Q: 48KN/m A B 8 m 8 m-

Q: find moment at point D, P=15kN

A: Given:- FBd of Beam;

Q: Assume you are an observer standing at a point along a three-lane roadway. AlIl vehicles in lane 1 a...

Concept explainers

Intersection Design

An intersection is a location where two or more roads or railways meet or join. The traffic movement is controlled at the intersection that depends on its design and type. It governs the operation, efficiency, speed, capacity, and safety of the highways, airways, and railways. The movement of the pedestrian causes hazards and delays at the intersection.

Question

100%

There are 11 vehicles observed in a 500 m section of a highway. The average time headway is 3 seconds. What is the value of the space mean speed in kph?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

2. In a 500 m section of highway, there are 10 vehicles observed. The timeheadway is 4 sec. Determine the space mean speed of the vehicles in kph. (5pts)
5) What is the minimum green time for a 35 feet wide intersection when the pedestrian crossing is being served? Consider the design walking speed of 3.5 ft/sec. A sports car is driving along a winding road designed by a transportation engineer. The vehicle accelerates from rest at a rate of 8 m/s2 for 5 seconds, then maintains a constant speed of 60 m/s for 10 seconds, and finally decelerates at a rate of -4 m/s² until it comes to a stop. Calculate the total distance traveled by the sports car. [Note that this problem uses SI units.]
D. There are 10 vehicles observed in a 450 m length of Aurora Boulevard. If the average time headway is 5 sec. calculate the space mean speed in kph
0-1 A section of highway having a length 60 m. The observed data are 6 vehicles cross over it in a period of 148 sec., for the following duration: 2.4, 2.8, 3.0, 2.1, 2.2. and 3.5 sec. Estimate the values of the flow rate, density, space-mean speed, time-mean speed, average gap, and average clearance. If the length of vehicles are 6, 5.4, 6.6, 4.8, 7.5, and 6 m respectively? 0-2 Traffic volume data has been collected for 10 min time intervals as shown below. Find the total hourly volume, flow rate and PHF. Time 7:30-7:40 7:40-7:50 7:50-8:00 8:00-8:10 8:10-8:20 8:20-8:30 Volume 250 280 300 200 150 130 0-3|| A vehicle takes 1.5 hr to travers a distance of 90 km between two cities. Calculate the journey speed and operational delay if you know that the running speed of this vehicle exceeds it journey speed by 10 km/hr ?
In a 500 m section of highway, there are 10 vehicles observed. The time headway is 4 sec. Determine the space mean speed of the vehicles in kph.
6. There are 5 vehicles passing through an intersection of two highway in a period of 20 seconds. Vehicle Spot speeds, kph 1 34.20 42.40 46.30 41.10 4 5. 43.40 Compute the space mean speed in kph. 41.05 kph
2/104 The two cars A and B enter an unbanked and level turn. They cross line C-C simultaneously, and each car has the speed corresponding to a maximum normal acceleration of 0.9g in the turn. Determine the elapsed time for each car between its two cross- ings of line C-C. What is the relative position of the two cars as the second car exits the turn? Assume no speed changes throughout. C b a b a 88 m 72 m Bla C Problem 2/104
A train starts from rest at station A and accelerates at 0.5m/s2 for 60 sec. Afterwards it travels with a constant velocity for 15 min. It then decelerates at 1m/s2 until it is brought to rest at station B. Determine the distance between the stations.
The following are specifications for traffic design of a highway:Speed of the passing car = 100 kphSpeed of the overtaken vehicle = 80 kphTime of initial maneuvers = 5 secTime passing vehicle occupies left lane = 10 secsDistance between the passing car and opposing car at the end of maneuver = 20 mAverage acceleration = 2.5 kph/sec. 1. Determine the required total passing sight distance for said road a. 502.75 m b. 602.75 m c. 702.75 m d. 402.75 m 1. Find the minimum required passing sight distance. a. 280.37 m b. 390.37 m c. 48.37 m d. 490.37 m
Calculate the passing sight distance on a two lane road having the design speed of 86 kmph and reaction time 2 sec. Assume one way traffic. Take acceleration of overtaking and overtaken vehicle as 3 m/s2 and 1.5 m/s2 respectively. Assume that overtaken vehicle starts accelerating after the reaction time of overtaking vehicle. Take space headway as 18 m.
What will be the theoretical capacity of a traffic lane with one way traffic flow at a stream speed of 40 kmph? [Assume the average space gap between vehicles to follow the relation s where V is stream velocity in kmph, t is = 0.278VŁ 8. %3D average reaction time = 0.7 sec and average length of vehicles 5 m]
What will be the non-passing sight distance on a highway for a design speed of 100 kmph when its ascending gradient is 2%? Assume coefficient of friction as 0.7 and brake efficiency as 50%.