Answered: valuate the hydrostatic force against…

valuate the hydrostatic force against one side of the plate by expressing it as an integral. (Recall that water has a density of 62.5 lb/ft3.)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Figure shown below is a gate in the form of circular arc with a central angle of 60° and radius 2m…

Q: A circular plate of radius 0.75 m is vertically placed in water such that centre of plate is 2 m…

Q: 1. A solid circular rod, 750 mm long and 30 mm diameter, is subjected to an axial force of 80 kN.…

A: Length (l) = 750mm dia (d) = 30mm Force (P) = 80kN Compression (∂l)= 1.35mm Change in diameter (∂d)…

Q: Two parallel plates kept 295mm a part have laminar flow of oil . The lower plate is stationary and…

Q: ۲/۱ العنوان Le olle и برات The pipe shown in figure has a mass of 800kg. Determine the forces acting…

A: As a subject matter expert in Civil Engineering, I can say that there are two main forces acting on…

Q: j.A square surface 3 m x 3 m lies in a vertical line in water pipe its upper edge at water surface.…

A: Given data : Dimension=3×3 m Density of water (ρ)=1000 kg/m3

Q: Water from a reservoir flowing through a pipe having a diameter of 500 mm with a velocity of 2.75…

Q: If a triangle of height d and base a is vertical and submerged in liquid with its vertex a distance…

Q: A 4 m long quarter clrcular gate of radius 3 m and of negligible weight is hinged about Its upper…

Q: A stream of water with a diameter of 25 mm strikes a flat plate with a velocity of 10 m/s. Determine…

A: Given Data Diameter of water jet (d) = 25 mm = 0.025 m Velocity of water (V) = 10m/s Find force…

Q: up B What is the total resultant force (kN) that is applied on surface AB? Then find the location of…

Q: 4. A water tank is made from 0.5 inch steel plate and has a diameter of 20 ft. Calculate the maximum…

A: In this question, first we will find force due to the weight of water. Then the opposing force T…

Q: 1.) The cylindrical drum is filled with water with unit weight of water 9800 N/m3. The cylinder is…

A: Note - Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the…

Q: Body A has a mass of 25 kg and body B has a mass of 50 kg. The coefficient of friction for all…

Q: A flat plate of 1.5 m² is being pulled over a fixed flat surface at a constant velocity of 10.5 m/s.…

A: Given data in question Area 1.5 m2 Velocity 10.5 m/s Distance 0.0025 m Force 4.1 N To find out…

Q: What will be the pressure difference between points A and B? X = 145 mm & Y = 77 mm. pair = 1.23…

A: To Determine The pressure difference between points A and B.

Q: Determine Determine the Maximum Tensile Flexural Stress. the Maximum Vertical Shear Stress.

A: Flexural strength of any beam is the stress at which bending failure occurs. It is also known as…

Q: The solid shaft is subjected to the following loads. Determine the diameter d of the shaft to the…

A: Determine the diameter d of the shaft to the nearest mm

Q: ottom as shown in the figure. Given d = 2.5 m and h = 1.9 m. Calculate the magnitude of the…

A: The resultant pressure force is equal to product of pressure at centroid and area of plane. Further…

Q: A) Water at 70 °C flows up a 50-ft-long conical pipe with its centerline sloping at 5° to the…

Q: A 2.8m square plate is completely immersed under water in a vertical position such that the two…

Q: Oil surface 2.1 m Water surface Oil 0.9 m Hinge Water 1.8 m

Q: ... А 30° 2.5m Water hinge L = 2m In the figure shown, a quarter circle gate AOB is hinged at point…

Q: 2 A rectangular gate AB hinged at A has a width of 2.0 m perpendicular to the paper and has…

Q: A 100 kg block is resting on a smooth inclined surface. Determine the value of T to maintain…

Q: . A rectangular open tank is 6m long, 2m deep and 2m wide is containing water up to lm height. f the…

A: b=2m h=1m L=6m

Q: A vertical triangular gate with Alcohol (SG = 0.78) on one side is shown in the figure. Determine…

A: The values and diagram given in the question are as follows: Specific gravity of alcohol(Sg)=0.78

Q: e weight of the block changes

A: Weight in air = 460N Height (h) = 0.5 m Width (w) = 0.3m t = 0.2m Body is half submerged

Q: A block weighs 460 N in air and has a dimension of h = 0.5 m, w = 0.3 m, and t = 0.2 m. 11. Find the…

Q: As shown in the figure compute the amount and location of the vertical and horizontal components of…

Q: In the swimming pool shown below, determine the resultant hydrostatic force and locate the center of…

A: To determine the resultant hydrostatic force and location of center of pressure on surface AB.…

Q: 1. Situation I. A 3 m square plate is immersed vertically in water such that the two edges of the…

Q: 0.5 in. | 105 in. A 2 ft The A-36 steel bar shown in the figure is constrained to just fit between…

Q: In the friction free shown, the following: compute B a. Pressure of the water in the tube at point…

A: Pressure is taken in absolute terms.

Q: A circular plate 2m in diameter is submerged in water with its higher and lower edges located at 2m…

A: Given :

Q: 3 A rectangular gate AB hinged at A has a width 2.0 m perpendicular to the paper, has a negligible…

Q: gitudinal stress along g force is developed

Q: A rectangular gate AB hinged at A has a width 2.0 m perpendicular to the paper, has a negligible…

Q: 6. A cubic tank is completely filled with water. What will be the ratio of the hydrostatic force…

A: To find: Ratio of hydrostatic force exerted on base and on any of the vertical sides

Question

A four-foot-high triangular plate with a six-foot-wide base is immersed vertically in water, with the top three feet below the surface. Evaluate the hydrostatic force against one side of the plate by expressing it as an integral. (Recall that water has a density of 62.5 lb/ft3.)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Problem 4. The pipe bend is in a horizontal plane. Oil (s = 0.88) enters the bend with a velocity of 3.50 m/s and a pressure of 280 kPa. Neglecting any energy losses in the bend, find the forces required to hold the bend in place. d = 200 mm d = 80 mm 65°
A square plate having one of its side equal to 3.2 meters is immersed in water in a vertical position such that the two edges of the square would be horizontal in order that the center of pressure shall be 8cm from the center of gravity. a. How far below the water surface should the upper portion of the plate be submerged? b. What is the distance of the center of pressure from the water surface? c. Determine the hydrostatic force acting on the plate at this position.
SITUATION. A closed cylindrical tank with 0.60 m diameter and 1.0 m height is fully-filled with water. The tank is rotated at 200 rpm. What is the pressure (kPa) at the circumference of the top base? O 34.74 O 44.55 29.55 O 19.74
A curved surface was submerged in water as shown. Calculate the vertical component of the hydrostatic force on the curved surface. The system is 2m wide into the paper. 5m 60° r = 2m
Show FBD and complete solution
Water flows at a rate of 120 L/s in a 30 cm diameter horizontal pipe connected to a 20 cm diameter pipe through a vertical reducer bend. The change in water direction of the reducing bend is 120o. The vertical distance between the entrance and outlet of the bend is 1.5 m and the pressure at its entrance is 70KPa. The total weight of the bend material and water contained in it is 90 kg. Calculate the horizontal and vertical components of the force required to hold the bend in place.
Determine the location of the total hydrostatic force acting on the 2m x 4m gate shown in the figure.
A 2.8m square plate is completely immersed under water in a vertical position such that the two edges of the square are horizontal. It is immersed such that the center of pressure is located 8cm below its center of gravity. Determine the distance of the center of pressure from the water surface. O 9.21m O 7.67m O 8.67m O 8.25m
Problem 4. The pipe bend is in a horizontal plane. Oil (s = 0.88) enters the bend with a velocity of 3.50 m/s and a pressure of 280 kPa. Neglecting any energy losses in the bend, find the forces required to hold the bend in place. d = 200 mm d = 80 mm 65°
A 2.8m square plate is completely immersed under water in a vertical position such that the two edges of the square are horizontal. It is immersed such that the center of pressure is located 8cm below its center of gravity. Determine the distance of the top of the plate from the water surface. O 6.8m O 6.3m O 7.3m O 7.8m
For some unknown reason