please solve for c Problem 7V₁=45VV₂=15VEnergy and Natural Response in Series Capst = 020nF3.0nF1005iThe switch has been openclosing at t=0. Determine:a) The initial energy in each capacitor.b) i(t)st<c) The energy delivered to the resistor, 0.<= < 00d) the final energy trapped in each capacitor @ t = ∞for a long time before

Given Circuit, Equivalent Capacitance can be calculated as, Ceq = C1C2C1 + C2Ceq = 20×3020 + 30 =…

V₁=45v V₂=15V 20nF 3.0nF 10052 T The switch has been closing at t=o. Determine: open for a long time before a) The initial energy in each capacitor. b) i(t) c) The energy delivered to the resistor, 0.≤t ≤00 capacitor @ t

V₁=45v V₂=15V 20nF 3.0nF 10052 T The switch has been closing at t=o. Determine: open for a long time before a) The initial energy in each capacitor. b) i(t) c) The energy delivered to the resistor, 0.≤t ≤00 capacitor @ t

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Find the result of the subtraction using 2’s complement method. A= 110101 B= 101000 a) A -B b) B - A

A: 2's complement of some binary number is got by adding 1 to the 1's complement number. All the…

Q: this root locus problem using manual calculations, please include the steps Please answer in…

A: In the given questions we need to plot the root locus.

Q: nd the poles for the X(s) s+3 then select the answers from the choices below. (s-1)(s2-2s+5) elect…

A: In this question we have to find out poles location with given transfer function...

Q: K C(s) R(s) 4 + 3s + s +2s + K

Q: Solve the network in Cauer-1 and 2 form

Q: Given the following state table and sequential circult, choose the correct optimized Input and…

Q: A) Determine the range of K for which the system is stable. K(s + 1) s(s+ 6) (S-1) 1+ B) Determine…

A: A. Need to find the range of k for which the system is stableB. Need to find any of the roots…

Q: xlm) =9 "[n-3]and A[n] = «[n +2] d. x[n] e. x[n] = e and h[n]=n

Q: Write a program in MATLAB that calculates and prints the result of the integral by using two-point…

A: Given, Write a program in MATLAB that calculates and prints the result of the integral by using…

Q: find the 2- Eruasform aR the funehing 1-- xCE ) - 1 (E+ HT) -> xt) = t (Z – 2T)

Q: Determine decimal values of the signed binary numbers expressed in 2’s compliment a. 01010110 b.…

A: In order to convert any base to decimal value each digit in binary is multiplied with their…

Q: Reduce the following block diagrams G1(s) R(s) C(s) G2(s) G5(s) G6(s) + + G3(s) G4(s) G7(s)

Q: can you please elaborate how did u find the cost what does R.H.S after = represents

A: The above question is based on digital circuit design using logic gates.Clarification has been…

Q: Show graphically the result of the convolution between (¼)^n u[n] and (u[n] - u[n - 3])

Q: R1 L1 C1 ww 1E-4 1E-8 e. For R1 = 200 Q determine the voltage across the capacitor as a function of…

A: Given:a circuit,with we need to find voltage across capacitor for t>0.

Q: Simplify the following expression using K-Maps F(A,B,C,D)=A'BD+AC'D+AB'+BCD+A'C'D

A: Simplifying the expression using K-map, A¯B¯ AB AB AB¯ C¯D¯ 0 0 0 1 C¯D 1 1 1 1 CD 0 1 1…

Q: Q// Draw the block diagram and find the state space. C(s) s2 – 2s R(s) s3 + 27s² + s

A: State-space- State-space analysis generally provides you a representation of the system in the space…

Q: Check the system stability using routh's criterion 1- D(s) = s3 + s2 + 2s + 24 2- D(s) = s5 +…

Q: The energy signals 10x(t) and 10 x(t-5) have the same energy. O True O False

A: The energy in a continuous time signal can be expressed as, ...... (1)Where, represents the…

Q: Find the range of K, using Routh Table for the system of Figure that will cause the system to be…

Q: C1 C4 v(t) C2 C6 C5 C3

A: CAPACITOR (C): A device that stores the electricity in the shape of an electrostatic charge is known…

Q: Complete the design using: • D-FF • JK-FF T-FF

A: The design using D-flip flop is as follows: The positive edge-set off D flip lemon is built from…

Q: Reduce the block diagram shown in the figure below to a single block, T(s)=C(s)/R(s)

Q: Consider the second order model as ë + 3x + 9x = ù + 2u. Draw 3 different block diagrams for the…

A: For the given system we need to draw the block diagram.

Q: How many infinite zeros and finite poles has the following open-loop system? s- 17 G(s) s(11 +…

Q: 176 This is a subjective question, her 2.2 Find 3650-84 23/0 for the given circuit…

A: In this questionWe need to determine the voltage Vo and current Io as shown the circuit. We are…

Q: C(s) R(s) 30 3 s+8s+9s+6s+s+30 2

A: To find the state space equation for the given transfer function

Q: Find the Thevenin equivalent at the nodes A-B. AV bA Js 207614 3A

Q: Q4) For the following system, determine the state space equation? dy d'y + 6 + 11 dt dy + 6 y = 6 i…

Q: Represent the system shown in Figure in state space where the output is 0(t). N 30 2N-m/rad 3…

A: Equivalent circuit for the given circuit is,

Q: 7. y= 14-x

Q: Design an ADC circuit using OPAMP

A: Drawing analog to digital converter using OPAMP. Here OPAMP act as a comparator through which…

Q: R(s) + H₁ G₁ + 四四 G2 G3 + C(s)

A: We need to reduce the above block diagram to get a result of C(s)/R(s).

Q: Solve the following integral problems using any method you want.

A: In this question , we will solve integral..

Q: Q-1Solve the differential equations by direct 1 dy method dx ( 1 mark) 4x² + 4x + 2

Q: Determine the currents i, iz and iz in the circuit shown below. (C- D)A (D– C)A DA 12 CA

A: Given circuit, Where, C=3 D=6

Q: VCE) is (1), R₂ FISCH) 1 C1 1₂. (C) Input → V(t) Output V₂(t) →>>> roon Ri √₂ (107²2 Find state…

A: The given circuit is shown below.The state variables are defined as and .Note:(i) Here is current…

Q: Solving for R using the Discharging curve equation: V(t) = 1.83V Vc = 4.96V C =4.7uF T = 50s V(t) =…

A: A RC circuit having V(t)=1.83 V.VC=4.96 V.C=4.7μF.T=50s.We need to determineThe value of R.The value…

Q: R₁ 나 → 5₂ R235 R3 C

Q: Solve the following differential equation ry + 4y = 1³-1

A: To solve this differential equation, we need to use the method of integrating factors. First, we…

Question

please solve for c

Problem 7
V₁=45V
V₂=15V
Energy and Natural Response in Series Caps
t = 0
20nF
3.0nF
1005
i
The switch has been open
closing at t=0. Determine:
a) The initial energy in each capacitor.
b) i(t)
st<
c) The energy delivered to the resistor, 0.<= < 00
d) the final energy trapped in each capacitor @ t = ∞
for a long time before

Expert Solution

Step 1

Given Circuit,

Equivalent Capacitance can be calculated as,

$C_{e q} = \frac{C_{1} C_{2}}{C_{1} + C_{2}} C_{e q} = \frac{20 \times 30}{20 + 30} = \frac{600}{50} C_{e q} = 12 n F$

And,

Initial voltage across the equivalent capacitance is,

$V (0) = 45 + 15 = 60 V$

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

No handwritten solution please
use convolution property to find time function of 1/6+5w-w2
Handwritten solution not acceptable
Find the Inverse Laplace of the following
Please give me the answer
Question Completion Status: a C2 C3 C1 Find Ceg at the (a,b) terminals given that C1-9.7 HF C2-2.8 uF C3-8.8 uF Ca-7.9 uF Note: Your answer should be round to the nearest single digit decimal place. Your answer will be in micorFarads. For example, if you compute 1.63x10-0, then enter 1.6 as your answer. 49 F P Type here to search Cop home iprt sc delete 144
Problem 4: Perform the following complex number operations and give your final answer in rectangular and polar fo Remember that you are allowed to use MATLAB or your calculator for these problems. (5 points each) a) 21265 7-19+j7 b) 30260+35280-70/130 -20260 10 c) + (8-16)(2+14) 20-j45 d) 12 + (8220)x(5-j10)
I need to solve this in the 30-minute course Control and Measurements course
Please answer in typing format solution please only Please answer in typing Ply i will be like it please thanks
Please could you use Matlab to solve this question and You must submit the Matlab commands/Simulink blocks you used as well as resulting outputs/plots in your answers. Please view the images attached for the question