V1 10V VR1 = VR2 = R1 5ΚΩ Hill V2 5V Find the voltage across and the current through each resistor using superposition. IR1 = units R2 = units units units R2 2ΚΩ

Q: draw an 8:1 multiplexer using 4:1 multiplexers

A: Need to draw the 8x1 multiplexer by using the 4x1 multiplexer. The design needs 2 numbers of 4x1…

Q: Q5/ The Gray code ( 1011011101)=

A:

Q: Suppose you have a 100MHz clock and five LEDs. Design a circuit which turns each and only one LED on…

A: According to the question, we need to design a circuit which turns each and only one LED on every…

Q: Can you design a zero crossing detector using comparator ? Explain with details MUST and draw the…

A:

Q: Find a state assignment for the following circuit: 1 A B/0 D/1 BA/1 C/0 C D/0 A/0 D| C/1_B/1

A:

Q: Q6/ Chose the correct answer for the output Q2 of the following circuit ( Assume that A= 1001101010,…

A:

Q: plot the output voltage when the resister and capacitor in the series branch and the resister and…

A: Given that, Case 1: One resistor and capacitor are connected in series, and input voltage is changed…

Q: Give different methods to compute discrete convolution

A: Given the question for discrete time convolution, INTRODUCTION : Convolution, one of the most…

Q: Can you redo this again? I need step-by-step solution, like there should be Step 1, Step 2, Step 3,…

A:

Q: If you want to convert a 2 V DC signal to 10 V DC signal, then the values of R1 and R2 should be

A: According to question: The gain of the op-amp is given as

Q: 7. A device has an input signal-to-noise ratio of 200 and an output signal-to-noise ratio of 7. What…

A: SNR is referred to as the signal-to-noise ratio and is frequently stated in dB. The quantity of…

Q: The offset voltage describes the dc component of a dc electrical .signal

A: according to the question we want to know what offset voltage describes

Q: If the input voltage Vi is a square signal. What will be the form of the output Voltage? (Write your…

A: Given op-amp circuit shown

Q: S1-The waveforms in the figure are applied to D-type FF. Accordingly, draw the shape of the signal…

A: Explanation: The above circuit of the D flip-flop shows that the triggering of the circuit is a…

Q: Q6) Analyze the counter shown in figure below. The most significant bit is C. The row represent the…

A: The solution is given below

Q: Construct

A:

Q: Circuit Theory: I have this following circuit but its not producing the correct output. My input is…

A: Please refer below pages.If you have any doubts please feel free to ask.Explanation:Step 1: Step 2:…

Q: Find all the prime implicants and essential prime implicants from the K-map below.

A: The prime implicants are the largest possible group of 1, where as the essential prime implicants…

Q: Find out the power of the following signal: x(n)=2ej3n Please show all the steps

A: For any discrete-time signal x(n), the power of the signal can be computed using the following…

Q: DESIGN SYNCHRONOUS (BCD) UP COUNTER BY USING JK FFs

A:

Q: Plz I need the answer of

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: I need to convert the drawing of drawing by hand to print a line on your computer please

A: It is given that:

Q: Write down state table of the following Circuit

A:

Q: Impedance inversion can be achieve using

A:

Q: 20k 55x2 +-60V ++ 500.0 #6 500 8:50 Vbe = 0.7

A:

Q: Sketch the waveform of vo. Indicate the maximum and minimum value 10 V E

A:

Q: Q9/Chose the correct answer for the output Q of the following circuit ( Assume that A=…

A:

Q: I sketeb out the fellewing signals: (a=5, b=3, c=2) a-) V = 15a(sin211000* ct) b-) V =…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub parts for…

Q: 3. The current that should pass through the RTD is: Оа. 5.7 mA O b. 10 mA Ос. 5 mA d. 11.5 mA

A: RTD , An RTD is a passive device The current that should pass through the RTD is

Q: srastb Ts Tp 'Te

A: Given: G(s) transfer function. And T(s) . And calculate: Value of Wn and Zeta and peak overshoot And…

Q: Find the state graph for the following parallel counter: A QB Q- TA QA Q T. QA TB Q. A clk clk clk

A: We will find next states for given sequential circuit.

Q: 11. What is the name of this circuit given below? (LSB). B (MSB) D 4567

A: The answer is in step 2

Q: Time taken for the response to raise from * 10 to 100 % is Setting time O Peak time O Delay time O…

A: Time taken for the response to raise from 10 to 100 % is  A. Setting time  B. Peak time  C. Delay…

Q: ane energy signals Find which of the signals on powes signals. Li) ucn) -ucn-6) (i) Sin ("an)…

A: Power signal: If average power is finite 0<P<∞, then the signal is a power signal. For a power…

Q: QUESTION 5 With reference to the instruction below ,what is the value of the number stored at the…

A: Choose the correct answer:

Q: If the load resistance is increased by 25%, the noise voltage will:

A:

Current Division Method

The generalized current divider formula is given by the following relation below,