Fill-up the TABLE with correct values. VOUTR1R1R2Ay = 1+R2Construct the non-inverting amplifier circuit as shownUse R2=1002, R;=1kQ, Vs=12V. The closed loop gain of the non-inverting amplifier isA, = 1 + R,/R, and VOuT = A,VINa. for an input peak-to-peak voltage of 50mV, construct a table anda plot of values quantifying the ratio between the output and input voltage fora range of frequencies from 1kHz to 6MHZ. Discuss your observations.Note: Fill-up the TABLE with the correct values below.FrequencyVoutAv = Vout/Vin1kHz2 kHz20 kHz200 kHz500 kHz1 MHz2 MHz3 MHz4 MHz5 MHz6 MHz

Answered: Image /qna-images/answer/148326c0-9892-4a53-b2ef-7d0093e32466.jpg

Answered: V.O IN νουτ R1 ww R23 Av = R1 1+ R2…

V.O IN νουτ R1 ww R23 Av = R1 1+ R2 on-inverting amplifier circuit as shown =1kN, Vs=12V. The closed loop gain of the non- A, = 1 + R,/R, and V, OUT = 4,VIN = AV *v' IN ww

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Give the value of the following resistors:(Must write final value to short notation using KOhms, MOhms, etc. if applicable) 6. Green, red, Orange, gold7. Blue, Violet, red, silver8. Orange, orange, red, silver9. Red, Orange, Green, gold10. Red, brown, black, silver
Please answer it ASAP for an upvote. Thank you. Instruction.All current must be in terms of milli-amperes (mA). All voltages must be in terms of volts (V). All resistor must be in terms of kilo-ohms(k-ohms).Round of your computed value on to four decimal places.
Module 10 Section Review 3.0.0.png Additional Resources Electronics Fundamentals: Circuits, Devices, and Applications, Principles of Electric Circuits, Thomas L. Floyd. New York: Prent 3.0.0 Section Review 1. The letter designation SL on an electrical draw- ing indicates a 4. A a. a. limit switch b. low-voltage switch c. load switch d. light switch b. C. d. 2. Existing power lines on an electrical site plan may be indicated by the letter 5. In t safe a. E b. I a. b. 2 С. Р d. V C. 2 d. 2: 3. The specific types of luminaires required in an installation can be found on the a. power plan b. electrical site plan c. schematic diagram d. lighting fixture schedule P Search for anything
Question 5 What is the device address used by the instruction OUT A4, AL?
*Explain the process here; how to determine the resistor value using the color coders and nominal range using the tolerance value* 1. Determine the resistor value, low and high tolerance (or range) for the following color- coded resistors Brown Black Red Gold a. Orange Black Brown Siver b. II. RESISTOR ERROR CALCULATIONS *Explain the process here and the data inside the TABLE, Explain Percent Error*
in the power max equation at the bottom of the page,why is the thevivn resistor multiplied by 4?
define engineering economics in 100 words.
What is the maximum number of digits that may be used in the Octal System?
Assume that the counter shown below is currently holding the value 1000. Keno Kleno RBI 7446 After 36 clock pulses, what value will you see on the 7-segment display?
The Radial Distributor can be fed at how many points O a. one point. O b. two points O C. any of the answers O d. middle point.
14] Encode Decimal '-124' using Two's Complement. Express your answer in Hex. 15] How much Current is passing through a 470 ohm Resistor that is dropping 3.3 Volts? Express your answer in Decimal with 2 digits of significance. 16] How many Volts are being dropped by a 2.7k Ohm Resistor if it is passing 75uA? Express your answer in Decimal with 2 digits of significance.
Solve the following values from alternating voltage measurements by the de Arsenval device using a bridge perfect 147.2 147.6 147.4 147.6 147.5 147.1 148.1 147.9 147.4 and finally 147.5 volts Calculate Certified real value! error rate standard deviation The measurement error for each value