V. 2x-a 2 -V ek An inverter which produces the output voltage shown the figure above is used to supply the series R (-10(Ohm]) and L(-20 (mH]) load. Determine the value of to produce an output with an amplitude of 90 V at the fundamental frequency for the DC input voltage 225 (Vl and the output frequency of 60 [Hz O 716899 [Degree O 510738 (Degree O 810000 (Degree) O 43.8645 [Degreej O 61.8853 (Degree) O87.7694 [Degreet 77.0324 (Degreel O 376821 (Degre)

V. 2x-a 2 -V ek An inverter which produces the output voltage shown the figure above is used to supply the series R (-10(Ohm]) and L(-20 (mH]) load. Determine the value of to produce an output with an amplitude of 90 V at the fundamental frequency for the DC input voltage 225 (Vl and the output frequency of 60 [Hz O 716899 [Degree O 510738 (Degree O 810000 (Degree) O 43.8645 [Degreej O 61.8853 (Degree) O87.7694 [Degreet 77.0324 (Degreel O 376821 (Degre)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A three phase inverter below has a Y- connected load. The inverter frequency is fo = 60 Hz and the DC input voltage Vs = 220V. The applied control signal is a 180 deg conduction mode. The RMS Line to Line voltage Vo is equal to 179.63V. The total harmonic distortion (THD) is equal to: Select one: a. 48.34% b. 31.08% c. None of these d. 100%
What is the effect of the temperature on the input dc voltage of a pv inverter? Why it is important to regard it during design
for square wave PWM inverter, Vdc=100V, L=25mH, R=1002, f=60Hz. draw the spectrum of the output voltage and current and then find the rms current value and the output power. Take n =1-20.
For single phase voltage source bridge inverter: 1- Draw th circuit. 2- With R=102, L=50mH, frequency is 50 Hz and supply voltage is 400V and square wave output, draw the waveforms of vo and io. 3- Calculate the RMS value of output voltage and mean output power.
A 1-phase full-bridge inverter is connected to a load of 4.2 . The DC input voltage is 40 V. What is the rms output at fundamental frequency?
Using the sine PWM method with the full bridge inverter below, it is desired to generate a voltage of 50 Hz on the serial RL load. A voltage of 120 V DC is applied to the input of the inverter circuit. Amplitude modulation rate ma -0.9 and frequency modulation rate mf -19. The resistance of the series RL load is 15 OHM and the coil inductance is 40 mH. a) What is the power drawn by the load resistor?b) What is the total harmonic distortion value (THD) of the load current?
In a lowering converter, the input voltage is Vs = 20V, the output voltage is Va = 10V, and the average value of the load current is Ia = 1.0A. The switching frequency is set to 50 kHz. If the inductance value in the inverter is L = 100 μH and the capacity value is C = 200 µF (a) the duty ratio of the switch D (b) the ripple / ripple (ΔI) value of the coil current (c) the ripple / ripple (Vc) of the output voltage and (d) the switching Calculate the maximum current passing through the element. Draw the waveforms of coil current (iL), switch current (isw) and diode current (i1) in the area below for a switching period according to these values.
Using the sine PWM method with the full bridge inverter below, it is desired to generate a voltage of 50Hz on the series RL load. A voltage of 120 V DC is applied to the input of the inverter circuit. Amplitude modulation rate ma = 0.9 and frequency modulation rate mj = 19. The resistance of the series RL load is 15 ohms and the coil inductance is 40 mH. What is the total harmonic distortion value (THD) of the power drawn by the load resistor and the load current?
Inverters create an ac voltage when only a dc voltage source is available. Select one: O a. True O b. None of the above O c. False Jump to...
Question: Which of the following statement is correct in connection with inverters Option 1: GTOS can bussed in CSI Option 2: Only VSI requires feedback diodes Option 3: VSI and CSI both require feed back diodes Option 4: Only CSI require feed back diodes
Simulation is NOT required. Please show calculations please. Thank you.
The inverter 74 ALSO4 has the following specifications IOHmax = -0.4 mA, IoLmax = 8 MA, IiHmax = 20 mA, IiLmax = -0.1 mA, Find the fan out.