V- belt 40kw 80rad/sec 20rad/sec D2 800mm

Q: If z₁ 1310 and 22 = = -15 +9i, determine the following: 4z₁ - 5z2 (Polar Form) COMPLETE THE MISSING…

A:

Q: Calculate y, the distance from the base to the position of the Neutral Axis of the T-section shown…

A:

Q: Question 29 Which of the following can change the hardness of a material? O Manufacturing process O…

A:

Q: pered gibs are adjusted by screws spaced out along the length of the gib

A: The statement mentions "Tapered gibs are adjusted by screws spaced out along the length of the gib".

Q: Which percentile is typically for designing lower-limit dimensions? - 95th 5th 50th 99th

A:

Q: Using the diagram, determine the maximum diameter for DIA B.

A:

Q: Answer by true or false for the following       Specific heat is a measurement of the ability of the…

A: The specific heat of a substance is defined as the amount of heat to increase the temperature of the…

Q: w of sine's when ( a= 100° , A=10.8 B=6

A:

Q: 2.34 Determine the resultant of the three forces of Prob. 2.22. Answer

A: Given:The three forces are:F1=800 NF2=408 NF3=424 N

Q: The solid shaft is subjected to the distributed and concentrated torsional loadings shown, where T =…

A: Given data T = 320 N-m The allowable shear stress for the material is Tallow = 185 MPa.

Q: Determine the maximum deflection of the 70-mm-diameter A-36 steel shaft.

A: To find: The maximum deflection of the 70 mm diameter steel shaft. Given: The diameter of a steel…

Q: Consider the following steel shaft with varying shaft diameter. Determine the rotation of D with…

A:

Q: 7. 8. is an important part of proper reservoir operation. filters protect a pump from dirt in a…

A: According to the given data 7.________filters protect a pump from dirt in a reservoir. 8.…

Q: Die Ntef d CW ad d 107 30T 167 327

A:

Q: Draw chalk diagram of all sections

A: To draw section views

Q: 2. Determine the reading on the vernier scale as indicated by the arrows. 25 30 35 40 10 20 30 40 50…

A: Least count of Vernier caliper = 0.02 mm

Q: 1. The built-up beam pictured on the right is subjected to an internal moment of M = 75 kNm. a) At…

A: *The internal moment acting on the structure is M=75 kNm. *The total length of the T section is…

Q: Place the labels with the most accurate description on the micrograph at locations A, B, and C, as…

A: given; Place the labels with the most accurate description on the micrograph at locations A, B, and…

Q: The steel box wrench (E=29,000ksi, v=0.32) is loaded with a 40-lb horizontal force and a 25-lb…

A:

Q: Represent the following combinations of units in the correct SI form:N/mm

A:

Q: В |C O2 4 D 3 A E (201 5 F D 6 H at c I G Needle

A:

Q: A Sluice gate is a device that is fitted in a sluice or fluid canal to operate and control the fluid…

A: We need to calculate the hydrostatic force acting on the sluice gate

Q: RIS R12 frant sew R32

A: Given 3D model To find Three views

Q: 4. Use F₁ =3, 6₁ = 2, k₁₂₁ = 4₁ K3 = 2,63 = 1, J₁ = 2₁ J₂=5, find the impulse and step response of…

A: Given: To find: Impulse and step response

Q: The L2 steel bolt as shown in Figure 4 has a diameter of 5 mm, and the link AB which is made from…

A:

Q: A force F = 6980 N acts upon a piston head, as shown in the figure. The gudgeon pin G connects the…

A:

Q: The rectangular lamina with breadth = 60 mm, depth = 30 mm. The Ixx value is _____________ mm4…

A:

Q: 0.250 DRILL THRU SIX HOLES EQUALLY SPACED 23° 30° CYLINDRICAL PLATE 1" STD 8 PIPE 3" XS BI PIPE 3"…

A: Section A-A represents the following thing.

Q: A hollow steel has an outside diameter of 5in. and it's inside diameter is 4in. What is the…

A: Outside diameter, do=5 inInside diameter, di=4 in

Q: What is the radius equivalent to Mohrs Circle?

A: Method to construct Mohr's circle, First Plot point A σx,-τxy, & B σy,τxy on σ - τ plane. Now…

Q: Draw the front, Side and top

A: According to the question we need to draw the three orthographic projection views of the given…

Q: Identify the drawings as isometric, trimetric, oblque or perspective. A. B

A: Isometric projection is a technique used in technical and engineering drawings to visually…

Q: Which corners would be visible from the FRONT orthographic view of this image. Select all that…

A: Front view will be like

Q: F = 120 lb | 30° 12 kN 1.25"- 30 4 m 1.5" 5 m 11"

A:

Q: Need you to draw orthographic views of this object.

A: The required orthographic views are drawn using third angle method of projection.

Q: How is the mohrs circle plotted? what values were plotted

A:

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.