Using the method of composite areas, determine the location of thecentroid of the shaded area shown in the figure

Q: olve moj and  the tabulatio

A: degree of static indeterminacy, Ds = no. of members + no. of unknown support reactions - 2* no. of…

Q: determine the shape factor and the plastic zone length sigma_{y} = 30OMPA 350 mm 200 mm 8 mm y 200…

A: Objective: To obtain Shape factor and Fully plastic moment of the given built up section.…

Q: For the figure shown, a. Determine the location of the centroid measured from the bottom (y). b.…

A: Fig-1Rectangle:Base=75+30=105mmHeight=25+30=55mmx1=1052y1=552-30=-2.5Fig-2Quarter…

Q: True or False Double integration Method is applicable to determinate beams only.

A: Macaulay’s method also called as (the double integration method) is a method used in structural…

Q: for part b, what happened to the t on the cty when integrating, can you please show this work again?

A: Given: u = A(1+bt) , v = cty  Required: To explain the stream line equation done in step 2 by the…

Q: Using Double Integration Method for the deflection of beams analyze the given structure below.

A:

Q: 2.5 k/ft Hinge 35 k B -16 ft- -8 ft 8 ft-

A:

Q: Determine the Reactions 3 m +1.5 m-1.5 m- 3 m 4 m C 2 m 4 m EN kN 2 m SN kN B

A:

Q: Solve the following using Double Integration Method lo kaN /ma いニ Aon =? man bm ル EI = lo00 kN-m2

A: given- simply supported beam with UDL  to find - maximum deflection.

Q: For the yellow region, calculate the following using THREE positive shapes and TWO negative shapes:…

A:

Q: Analyze the continuous beam shown in Figure by drawing the shear and bending moment diagram and…

A:

Q: Using Solpe Deflection Method Caluclate the MB, MC and MD.

A: EI = Constant Determine the moment at point B, C and D using Slope-Deflection Method.

Q: SIT A. Determine the slope and deflection at point B of the beam. 50 kN · m - 4 m El = constant E =…

A: Given  E=70GPaE=70×103 MPaI=160×106 mm4 Consider the diagram of the beam

Q: determine the linear error of the closure.

A: Given Data - To Find - linear error of the closure.

Q: Contrast between: a- Apparent and true dip. b- Apparent and true thickness

A: Contrast Between Apparent and True Dip: S. No.                 Apparent Dip…

Q: 3. With line XY as the outline of a plane mirror (see diagram below), draw a triangle ABC as shown…

A: Given data- XY is acting as the mirror.Traingle ABC is on front of mirror and acts a object

Q: Im 3m A Im 5m 3m 5m 50KN 50 KN 80 KN Find the axia) stresses of member and state if its tensile or…

A: With the help of method of Joints, Forces in members BD,CD,CEFirst calculating basic reactions of…

Q: The measurements x1 = 8m, x2 = 6m, and x3 = 4m represent the sides of a rectangular parallelepiped…

A: The values given in the question are as follows x1=8 m x2=6 m x3=4 m Systematic errors are ∆x1=0.004…

Q: I. Solve the given truss 69 in k 69 in k 10 9 ft 30 12 ft 12 ft 12 ft A. SOLVE MEMBERS EC, ED AND CD…

A:

Q: The net area in shear, Anv, of the L6x6x3/8 angle shown in the figure is equal to

A: The shear will act parallel to the gusset plate and will be from left end of gusset plate to the…

Q: WoL? M = - WoL' 6. 24EI WL2 Wor? (:0-10Lx+ 5Ľx?-x) 120L WL WL WL Ely = 30EI 1SEI 3 12EI

A:

Q: E4. A man uses his hand to measure the width of a tabletop. If his hand has a width of 12 cm at its…

A:

Q: Given: E= 20.5 GPa and I= 6.75x 10$ mm² where the Moment of Inertia of AB is 1.51 Analyze the frame…

A:

Q: Determine the area and the centroid (x, y) of the area

A: In solid mechanics, there can be any possible shape of the cross-section, for analysis of various…

Q: Determine the centroid of the lines that form the boundary of the shaded area shown.   Determine:…

A:

Q: A closed transverse has the following data.  Find the value of D, E, F.

A:

Q: A transmission cable 300m long, weighs 600 kg. The tensions at the ends of the cable are 400 kg and…

A:

Q: EQUILIBRIUM ooth- ring D 5' Boll and socket! CHAP. 4- ^. 4-121. The homogeneous block of Fig. P4-121…

A: Solution-The given values are as follows,The specific weight =50lb per cu ft The force acting…

Q: Problem 2: Inputs: ● ● ● ● A = (3, 3) ft B = (9, 12) ft C = (3, 1) ft D = (9, 6) ft same as previous…

A:

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.