Using the force method of analysis, determine the reactions at the supports then draw  the shear and moment diagrams for the beam shown in in the diagram Assume the support at B is  a roller. Use the moment at A as the redundant

Q: Determine the reactions on the supports. El is constant .(Solve using Stiffness method) 150 kN B…

A: The following figure shows the Free Body Diagram of the beam. Adopt the Stiffness Method to solve…

Q: In a simply-supported beam loaded as shown below, the maximum bending moment in Nm is 1000 mm 500 mm…

A:

Q: 4

A: Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: solve the differential equation of the deformation of the beam below.

A:

Q: A roof truss is loaded and supported as shown in Figure 2. The joints are all pinned. Take L = 3 m…

A: Given data:

Q: Determine the MOMENTS acting at the ends of each member of the frame shown below. Assume the…

A:

Q: For the system shown, a. Determine the equivalent force-couple system at the base at C. Express the…

A: Given:

Q: Calculate the moments at the joints and supports. Draw the shear and bending moment diagram. Support…

A: Fixed ends moment:   MFAB=-wl212=-32*2212=-10.67 KN.MMFBA=wl212=32*2212=10.67…

Q: 3. For the beam shown below, let wo = 90 N/m and w1 = 50 N/m. Wo W1 В -2 m-2 m 3 m Figure 2 Loaded…

A:

Q: (Beam-like structure with two forces P applied at an angle x = 20°. This structure has a double…

A: Given data:

Q: For the beam and loading situation shown in the figure; (a) Draw the free body diagram. (b)…

A:

Q: Using th Ford Ahalysis, determine the support reaction Of the beam she is constant. The support at…

A: Given:- udl=4kN/m To find:- support reactions

Q: The simply supported beam is subjected to the force F-550 N and the uniform distributed load with…

A:

Q: Determine the reactions at the supports, then draw the moment diagram. Assume the support at B is a…

A:

Q: A frame EFG is shown in the figure. All members are prismatic and have equal flexural rigidity. The…

A:

Q: A 100 mm B C 50 mm E DO

A: To find the force in each bar and horizontal movement of point A-

Q: THE 6-M POLE ABC IS ACTED UPON BY A 455- N FORCE AS SHOWN. THE POLE IS HELD BY A BALL-AND-SOCKET…

A:

Q: In the truss shown in the Figure, the force in member BC is: 100t 30 a. 100 Tons (C) b. 100 Tons (T)…

A: Given data in question  Truss  Point load Span member length  Angle To find out  Force in member BC

Q: Determine the reactions at the supports A and B, then draw the shear and moment diagram. EI is…

A: Given thatFree body diagram of the loads and reaction as shown below ,       Neglect axial load…

Q: 6 m B 240kN/m 6 m 4.5m 750kN/m D

A:

Q: The beam supports a uniform load of 3.0 k/ft and a concentrated load of 12 k as shown in the figure…

A: Calculate reaction at support B and D: ∑FV=0RB+RD=48 ∑MB=03×12×6-12×6-RD×24=0RD=6kRB=48-RD=42 k

Q: Statics and Equilibrium The beam supports 2-triangular distributed loads. The weight at the peak of…

A: The shear force is a surface-sensitive force. The reaction that is induced in a structural element…

Q: A 2 m 200 kN 2EI 3m 45 kN/m pozun B ΕΙ 5 m

A:

Q: 5. The Fink truss shown in Figure 1-63 is supported on rollers at A and hinged at B. The uniformly…

A: Solution-The given diagram is shown below, To Determine  The reaction  ata A and B

Q: Determine the MOMENTS acting at the ends of each member of the frame shown below. Assume the…

A:

Q: Use the Müller-Breslau principle to sketch the influence lines for the vertical reaction at A, the…

A: Use the Müller-Breslau principle to sketch the influence lines for the vertical reaction at A, the…

Q: For the following indeterminate truss (with SI = 1) determine all the member forces using the Force…

A:

Q: Find the force in truss DE. T = 390 N, x = 1.8 m. (Note: if the force in the truss is in tension,…

A: Joint method is used to calculate tension or compression in members of a system on which some load…

Q: Determine the MOMENTS acting at the ends of each member of the frame shown below. Assume the…

A:

Q: Situation B. The cantilever beam shown is in an equilibrium state, 25kN 10KN 50KN/m 60 A 3m 2m 4m 1m…

A: solution for question 7 vertical  component of 10 KN load  Fv=10sin60°=8.66 KNmoment about…

Q: use the method of superposition to solve the reactions at the supports.EI is constant. 2. Determine…

A:

Q: Determine the components of the P kN force. The components must parallel and perpendicular to the…

A: Given  P = 10KN  Angle of force  = 20⁰

Q: 1- Determine the reactions at the supports and draw the moment diagram of the statically…

A:

Q: a. Find the value of the moments at the ends of each element. b. Find the value of the horizontal…

A: For the given frame we have to find moments at the ends of each element and horizontal reaction at…

Q: A trapezoid is shown in the figure. 1. Compute the area of the trapezoid. 2. Compute the Centroid of…

A: Given Trapezoid with dimensions. To Compute 1. The area of the trapezoid. 2. The Centroid of the…

Q: d (mm) P(kN) Q(N) Oallow (MPa) s (%) 20 18 80 12 40 1 (a) The structure shown in Figure Q3 is…

A:

Q: Part A.) what are reaction forces Cz act and Mc part C.) as shown  Part d.) as shown  please…

A: Cantilever beam with moment at free end and distributed load acting over segment BC is given. We…

Q: Q5 Draw the influence line for (a) the moment at B, (b) the shear at C, and (c) the vertical…

A: Given data:

Equilibrium and Support Reactions

Civil engineers deal with structures that are composed of several members connected or with individual members such as beams and columns. To analyze such structures, the condition of statics must be applied. Under the static condition, the members are considered to be in equilibrium under the action of forces, that is, the members are assumed to be having negligible velocity.