lc (mA)90 LA80 uA70 HAVer=IVV- 10 V60 HA100(Saturation region) 550 μΑVo= 20 V9040 LA8047030 LA603(Active region)5020 μΑ4023010 HA20101520 Vr (V)100.20.4060.81.0Var (V)(Cutoff region)(a)(b)FIG. 3.132. Using the characteristics of Fig. 3.13a, determine:a. Bac at le = 60 µA and VcE = 4 V.b. Repeat part (a) at la = 30 µA and VCE = 7 V.c. Repeat part (a) at ls = 10 µA and VCE = 10 V.d. Reviewing the results of parts (a) through (c), does the value of Bac change frompoint to point on the characteristics? Where were the higher values found? Canyou develop any general conclusions about the value of Bac on a set ofcharacteristics such as those provided in Fig. 3.13a?

The plot given in Fig 3.13(a) is the output characteristics of a transistor. The formula to compute…

Using the characteristics of Fig. 3.13a, determine: a. Bac at le = 60 µA and Vce = 4 V. b. Repeat part (a) at le = 30 µA and VE = 7 V. c. Repeat part (a) at le = 10 µA and Vce = 10 V. d. Reviewing the results of parts (a) through (c), does the value of Bac change from point to point on the characteristics? Where were the higher values found? Can you develop any general conclusions about the value of Bdc on a set of characteristics such as those provided in Fig. 3.13a?

Using the characteristics of Fig. 3.13a, determine: a. Bac at le = 60 µA and Vce = 4 V. b. Repeat part (a) at le = 30 µA and VE = 7 V. c. Repeat part (a) at le = 10 µA and Vce = 10 V. d. Reviewing the results of parts (a) through (c), does the value of Bac change from point to point on the characteristics? Where were the higher values found? Can you develop any general conclusions about the value of Bdc on a set of characteristics such as those provided in Fig. 3.13a?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the given circuit: if V, = 15, Iz= 17 mA, IzK = 0.25 mA, Z, = 14 2, P,(max) = 1 W, answer the following questions: a) Determine the minimum load current I(min) for which the zener diode will maintain regulation. Assume R = 200 2. Explain your answer b) Determine the maximum load current I (max) for which the zener diode will maintain regulation. What is the minimum value of R, that can be used? What is the range of R, for which regulation is maintained? c) Repeat part (a) when R=10 Q. R IT Iz VIN RL 24 V +
Please in detail ,asap
The diode current in a p-n junction is modeled exponentially (given below.) When the p-n junction is polarized with 0.7V and 0.75V, the currents flowing through the diode are again measured on the basis of 1.36 mA and 7.20 mA. Accordingly, what is the ideality factor? (Note: Take the thermal voltage as mV)
For the Zener Diode network shown if the Fig. Determine VL, Vr, Iz, and Pz.
Q3: Find the intrinsic carrier concentration in silicon at (a) T=200K, (b) T=400K. The values of N. and N, are 2.8x1025/m³ and 1.04x1025/m³, respectively. (Ans: (a) 7.68x101/m, (b) 2.38x1018/m³)
Please provide Handwritten answer
Can you solve this question by explaining your solution step by step and giving details on the formulas and calculations, please. Thanks a lot. 2) Consider a two terminal semiconductor diode a) Calculate the thermal voltage of a diode at room temperature about 27oC b) Calculate diode dynamic resistance in case of 13 mA diode current. (Boltzman’s constant is 1.38x10-23 J/K, and magnitude of electron charge is 1,6X10-19 C)
estion 3: For the circuit given here, Write the expression for Vout in terms of the Vin, R1, R2 and R3. Vout? +8 V R₁ 1K R₂ 3.3K 1N5230B 4.7 V Zener D₁ www R3 1K +5 V For given values of Vin, the resistor values and zener diode rating, calculate value of Vout
clear and correct or dislike
answer i), ii), iii), iv) and include the solution of the graph and the graph itself
For the circuit shown, for what range of Vilt) will the diode be off. 1K Vk = 0.7V 1K )Vi(t) 1K +) 2v a. Vi(t) greater than 2.7V O b. Vi(t) less than 1.7V c. Vi(t) less than 3.7V d. Vi(t) less than - 4.6V. O e. Vi(t) greater than 8.5V. O f. Vi(t) greater than 4.6V. g. Vilt) less than 8.5V. O h. None of the listed range O i. Vi(t) less than 2.7V
Given circuit network below, Determine the range of values R_ that will maintain Zener diode on if Vi = 20V. Determine the range of values Vi that will maintain the Zener diode on if R = 1.2kQ + 220 N Vz = 10V Pzmax = 400mW RL V;