Using SDM for the frame shown below, determine the following structural parameters, FEM and support moments;20 kN24 kN/m5 m21A18 kN/m3.2 m2.8 m-1. The value that most nearly gives the absolute value of Fixed-end moment (FEM) at joint A of member AB in kN-m, FEMAR I Select J2. The value that most nearly gives the absolute value of Fixed-end moment (FEM) at joint C of member BC in kN-m, FEMCB [Select]3. The value that most nearly gives the absolute value of the Moment at C in kN-m, [Select ]3. The value that most nearly gives the absolute value of the Moment at C in kN-m, [ Select ]*must be the same with no. 3 above4. The value that most nearly gives the absolute value of the Moment at B of member AB in kN-m, MBA [ Select]4. The value that most nearly gives the absolute value of the Moment at B of member AB in kN-m, MBA [Select]*must be the same with no.4 above

CALCULATE of FEM and End Moments using SLOPE DEFLECTION METHOD

Answered: Using SDM for the frame shown below,…

Engineering

Civil Engineering

Using SDM for the frame shown below, determine the following structural parameters, FEM and support moments;

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

I'm trying to figure this code out in jupterlab
Problem 6.42 Consider the truss (Figure 1). Suppose that F = 14.5 kN Figure 1 4 kN of 1 6 kN H B m G 2 m 9 KN C -1.5 m 1.5 m 1.5 m 1.5 m 1 m D > 6 kN E Part A Determine the force in member BC. State if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. FBC = Submit Part B FHC = D μA Submit Value My Answers Give Up Determine the force in member HC. State if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. Units μA Value Units ? My Answers Give Up ? Part C Determine the force in member HG. State if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of…
: Compute the support reactions and member forces for the given truss as shown in Fig.3 using Displacement method (Stiffness method). Take EA= constant. 20 k 20 k EA= Constant 10 ft 10 ft K10 ft- Fig.3
For a 2D truss with 10 nodes, only 4 nodes are supported and they are all pinned. How many Degreesof Freedom of this model are NOT constrained?
Help me solve as soon as possible
The inextensible, rigidly jointed frame illustrated below is fully fixed at D and E and has a simple support at C. The rigidities of elements AB, BC and BE are indicated in the diagram, where as 2.5.-1.5 and as-4.4. The member lengths are given by L₁= 3.8 m, L₂= 3.1 m and Ly=2.3 m What is the distribution factor DFBA associated with node 8, to 3 significant figures? 9₁(EI) L₁ Clear my choice Ⓒa 0.162 b. 0.224 OC None of the available options O d. 0.215 O.0.256 OF 0,644 B a (EI) a₂(EI) ** L₂
A wide flange is used as a beam that is simply supported at its ends.The properties are shown.A = 19600 mm². by = 229 mmL = 1249 x10^4mm te=14 mm Tx = 25.4 mm tr = 24.9 mm ly = 49.5 x10^4mm d = 623 mm Ty = 50.5 mm If the beam is laterally supported at supports only, determine the allowable bending stress for a length of; 1. 2m 2. 4m 3. 6m 4. 8m
Calculate the support responses and the bond strengths at the C-joint of the carrier system given in the figure. 6 kNm 4 KN 4 KN 4 kN/m B 1m A 4 m 6 m 10 KN +2m +2m D 3 m F
A portal frame shown in figure (not drawn to scale) has a hinge support at joint P and a roller support at joint R. A point load of 50 kN is acting at joint R in horizontal direction. The flexural rigidity El, of each member is 10° kNm?, under the applied load, the horizontal displacement (in mm, round off to 1 decimal place) of joint R would be 5 m EI EI 10 m R 50 kN
For a plane truss member, the length is 2 m, E = 200 GPa and area of cross-section is 200 mm². The stiffness matrix coefficient K₁1 with reference to its local axis is A) 200 N/m B 2 × 107 N/m C) 4 x 107 N/m с D) 400 N/m
1 1 20 ft 18 k 10 ft 15 ft constant El Part B 10 k 2 3 15 ft Determine the reactions and the member end forces for the beam shown in A1 using the matrix stiffness method (Problem 17.4 of Structural Analysis, 6th Edition, Aslam Kassimali).
For the truss shown in the following figure, the temperature of member BC is raised by 110 °C, and member BD is raised by 70 °C. EA=300000 N for all members and a=1/75000 1/°C. Use the stiffness method to do the following: b) Ay = c) B₂ A | C ΤΙΣ Part 1. Calculate the displacements at the joints: a) Az = d) By = e) C₂ mm mm mm mm mm Part 2. Calculate the force in each member: a) NAB = b) NAC = c) NBD = d) NBC = e) Ncp = f) NAD = 5 m N N N N N N B D 5 m