Using Kirchhoff's rules, find the following. (E, 71.0 V, E₂ 60.4 V, and E, = 79.8 V.)M2.00 kwwR₂8₂4.00 knwwR₂R₂5,00 kn48,Q(a) the current (in mA) in each resistor shown in the figure aboveMAIn"MA18₂MA(b) the potential difference between points c and f(Give the magnitude of your answer in volts and select the point of highest potential.)magnitude of potential differencepoint at higher potential(c) What If? If all of the resistors in the circuit were decreased in value by a factor of 1,000, would the current in each resistor simply increase by a factor of 1,000? Explain your answer.

Answered: Image /qna-images/answer/423b1528-a06c-4e47-b7cb-d166860715fe.jpg

Answered: Using Kirchhoff's rules, find the…

Similar questions

(a) A 34.9-m length of copper wire at 20.0°C has a radius of 0.23 mm. If a potential difference of 7.00 V is applied across the length of the wire, determine the current in the wire. (Use the values in the following table.) Material Resistivity (2. m) Temperature Coefficient of Resistivity a [(°C)-¹] 1.59 x 10-8 Silver Copper Gold Aluminum Tungsten Iron Platinum Lead Nichrome Carbon Germanium Silicon Glass Hard rubber Sulfur Quartz (fused) 1.7 x 10-8 2.44 x 10-8 2.82 x 10-8 5.6 x 10-8 10.0 x 10-8 11 x 10-8 22 x 10-8 1.00 x 10-6 3.5 x 10-5 0.46 2.3 x 10³ 1010-1014 *1013 1015 75 x 1016 3.8 x 10-3 3.9 x 10-3 3.4 x 10-3 3.9 x 10-3 4.5 x 10-3 5.0 x 10-3 3.92 x 10-3 3.9 x 10-3 0.4 x 10-3 -0.5 x 10-3 -48 x 10-3 -75 x 10-3 (a) All values at 20°C. All elements in this table are assumed to be free of impurities. (b) See the section "Resistance and Temperature". (c) A nickel-chromium alloy commonly used in heating elements. The resistivity of Nichrome varies with composition and ranges between…
A copper wire has a length of 34.0 m and a resistance of 5.00 2 at 20.0°C. Assuming a circular cross-section, what is the wire's diameter (in mm)? The resistivity of copper at 20.0°C is 1.70 x 10-8 0 m. mm
Help me with this question
Question 1 If Ri = 36 Q, R2 = 76 Q, and R3 = 110 Q, find the current through R1. Source of emf 1 (E1) = 15 V Source of emf 2 (E2) = 29 V R, R, E WAWA R, wwW E, ROUND OFF ANSWER UP TO 2 DECIMAL PLACES. INPUT BOTH THE NUMBER AND UNIT (LETTER ONLY). INCLUDE THE SIGN IF THE ANSWER IS NEGATIVE.
Given the temperature coefficient of resistivity of a certain wire to be 3.1 x10-3 (°C)-1.By what factor is the resistance of this wire changed when its temperature is increased from 20.0°C to 79.48 °C? R Ro
In the figure resistor 1 = 126 2, resistor 2 = 81 N, and the ideal batteries have emfs ɛ1 E2 = 5 volts, and ɛ3 = 7 volts. Find the current through resistor 1. = 29 volts, Round off answer up to 3 decimal places. Consider absolute value. Include the unit (A for ampere, V for volt and ohm for ohm). Rz RI ww
Determine the length (in mm) of a gold conductor that has a resistance of 0.014 Ω and a cross-sectional area of 2.7 x 10-9 m2. The resistivity of gold is 2.2 x 10-8 Ω-m [round your final answer to one decimal place].
An aluminum rod has a resistance of 1.585 2 at 23.0°C. Calculate the resistance of the rod at 136.00°C by accounting for the changes in both the resistivity and the dimensions of the rod. Round your answer to the nearest thousandth and write it in the answer section. For aluminum: Temperature resistance coeff. ¤f = 3.90 X 10-3 °C-1, length expansion coeff. a = 24.0 X 10-6 °C-1.
160% P 2:35 Asiacell I. H.W -2.pdf H.W -2 6. For the circuit board in Fig. 7.66: a. Find the total resistance Ry of the configuration. b. Find the current drawn from the supply if the applied voltage is 48 V. c. Find the reading of the applied voltmeter. 6.8 kf V 1.2 k? 3.3 kN 2 kn Rr - 2.4 k2 48 V FIG. 7.66 Problem 6.
What temperature should a copper wire (which is originally at 20°C) reach to increase its resistance by 12%? Information: alpha = 0.0068 (C^-1) Help: The final resistance of the copper wire is R = 1.12Ro Write your answer with 2 significant figures.
The resistivity of copper is 1.72E-8 Ω·m. We would like to use a copper wire to connect two devices that are 6.65 m apart and require the wire resistance to be no higher than 7.21E-3 Ω. What is the minimum cross section area of the copper wire that we should use (in m2)?
Consider the circuit shown below. Find V, (in V), 1, (in A), and I, (in A). (Due to the nature of this problem, do not use rounded intermediate values in your calculations-including answers submitted in WebAssign. For the currents, indicate the direction with the signs of your answers.) 1 = 7 A 12 R, = 18 Q R, = 9 0 V2 = 28 V V R3 = 3 0 V V = I, = I3 = A

SEE MORE QUESTIONS