Using Kaiser's formula, estimate the order of a linear phase bandpass FIR filter with the following specifications: passband edges fp1=0.35kHz and fp2=1kHz, stop band edg fs1=0.3kHz and fs2=1.1kHz, peak passband ripple ap=0.1dB, minimum stop band attenuation as=54DB, and sampling rate Fs=10kHz.

Q: After reduction, the current - caring capacity of a condenser is referred to as the___. A. ambience…

A: Given: After reduction, the current carrying capacity of a conductor is referred to as the ___.

Q: The symbol for a thermostat consists of a ____ with a T in the middle.

A: we need to fill in the blank for the statement:    the symbol for a thermostat consists of a ____…

Q: Briefly explain the working of following power plants a) Thermal Power plant b) Hydel power plant

A: thermal power Plant coverts heat energy to electric power / Energy. The basic principle of these…

Q: What spaces are not included in floor area when calculating the load in volt amperes per square…

A: For calculating the load, first evaluated the total floor area. And according to the NEC , the total…

Q: Count Mounting method 15. From the information you have studied about the various electrical…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: REVIEW Refer to the National Electrical Code or the working drawings when necessary. Where…

A: Here it is asked to solve question (2), so we are solving that question only. Given information to…

Q: List and explain types of Fire Extinguishers. What's the difference between Mechanical safety vs.…

A: Both more formal visual inspections and routine, informal "before use" visual checks enhance safety.…

Q: IS it a requirement to have a light ixture outside the garage door for a vehicle? O No Yes For two…

A:

Q: Is there a way to clean up this answer by using proper notation

A:

Q: What type of order is given by a governing agency that finds a violation of the Electrical Code…

A: Electric Code rules:- A building's electrical wiring must adhere to a set of rules known as the…

Q: The instrument used to make drawings to scale is called a(n) ____ scale

A: The instrument used to make drawings to scale is called a(n) ____ scale Fill the blank

Q: Please provide a comprehensive explanation of what ring counters are as well as how they are used.

A: Introduction Ring Counters: Ring counters are the type of sequential digital circuit that is used…

Q: . Explain about Fuel cells?

A: Fuell cell

Q: Generators can be connected to the electrical system of the residence in several ways (Select all…

A: Generators can be connected to the electrical system of the residence in several ways

Q: The subject is engineering and it is from the textbook "AutoCad and its applications"  1-Describe…

A: Since this question contains more than one sub-part, as per the guidelines, first 3 sub-parts has…

Q: What is the meaning of calculated load?

A: Since many different loads are connected to an electrical supply, it is extremely important to know…

Q: Does ‘a three digit color coding of resistor values’ limit producible resistor value ranges? Why? If…

A: Solution Yes color coding of resistor values limit the resistor value range. In colour coding of…

Q: Explain what this matching box is. Describe the parts

A: The given diagrams are shown below. It is asked what is this matching box and also it asked to…

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.