Using Ford-Fulkerson's Method. Calculate the capacity in megalitres/hour of this pipe system.

Q: Copper interconnections are introduced into state-of-the-art ICs because of its lower resistivity of…

A: Given; Resistivity (r)= 1.66µW.cm. Thickness = 1µm Width = 10µm die side Length =  20mm ab→= l…

Q: If the transient response of a given system settles within 5% in 9.6 Sec then the extra time…

A: Given that if the transient response of a given settles within 5% in 9.6 sec then the extra time…

Q: 3. Find the Equivalent resistance R, and current i. 13 2 a 24 2 10 2 20 2 210 V ww

A:

Q: What gas do plants give off in the light

A: The correct answer is oxygen(O2).

Q: c) Show the computed shear and over-turning moment on the following graphs. FR P5 F4 r3 F2 BASE…

A: Step 1: Define the Point of Interest (POI):Identify the specific location in the structure where you…

Q: ain and output voltage if h-150 Bp-5000,rop-2MO. 24V 3M Ohm 5k Ohm 70 k Ohm 10 uF onm

A: The original circuit was reduced by calculating the equivalent of sources and resistances at the…

Q: Calculate the COPT for system including following unit is: ITI Unit No Capacity (MW) FOR 1 25 0.03 2…

A: Capacity Outage Probability Table is a good indicator for determining future capacity expansion to…

Q: 1 μm particles at equilibrium charge distribution will consist of many multiple charged particles of…

A: True

Q: -) Figure 1.1 Unregulated Power Supply Theory Using the above formula compute the ripple (the) for…

A: The ripple factor is described as. The ratio of the RMS cost of an alternating present day component…

Q: Q. No. 5. Find the

A: Detailed explanation is given below

Q: R2 R1 RL R3 Given 1 = 4 A R1 = 72 R2 = 20 R3 = 32 For the above circuit, determine VTh and RTh to…

A: we need to calculate Vth,Rth,RL,Pmax

Q: Which of the following word equations describes the material balance simplified for a "closed"…

A: Given, equations for material balance. To choose the correct answer for closed system with no…

Q: 2 resistor using Ohm

A: 1 Current through 1 ohm is 20 amps 2. Equivalent Resistance = 64 ohms

Q: 1. By using the tincker-cad Set up the equipment as given below make sure the resistance value is…

A: According to the information given:- I am using TinkerCad to setup this equipment with resister…

Q: Suppose that a (pA = 0.1, ps = 0.2, A = 1 min)-BSSQQ is operating in steady state. Calculate EQ(0).

A: Given information: It is given that pA = 0.1, pS = 0.2 and delta = 1 min-BSSQ.

Q: R1 3 Ohms Node 1 R3 4Ohms Node 2 R4 4 Ohms Vi=40V R2 2 Ohms V2= 20V Rs 5 Ohms

A: Given: For the circuit given in figure 7 apply Node Voltage Analysis and voltage and current across…

Q: Given the circuit with input of 80HZ, • Find the turns ratio • Find Vp(sec) • Find Vo when capacitor…

A: Solution for above problem is given below -

Q: Calculate the power required (P) for maintaining the cabin temperature, when the COP of the…

A: "350" power required (P) for maintaining the cabin temperature, when the COP of the…

Q: Q.1 Draw Flow chart of the steps for analyzing the beam to find the reactions in (Figure 1). by…

A:

Q: Assuming the number of transistors per square inch is 6 Billions today. Use Moore' s law (doubling…

A: Moore's Law states that the number of transistors on a microchip doubles every two years. The law…

Q: Draw the circuit diagram for the given expressions. Show the diagrams on your solution sheet. 1. F =…

A: Here, we are given two expressions and we have to draw the logic circuits. Logic circuit diagram can…

Q: 3.20 Calculate / and the current /for V= 700 mV for a pn junction for which N, = 10/cm 200 um, n, =…

A: Solution:   Given, V = 700 mV NA = 1017 /cm3 ND = 1016 /cm3 A = 200 µm2 ni = 1.5 x 1010 / cm³, Lp =…

Q: Draw bezier curve for the given control points p0(1,4) ,p1(4,8), p2(6,1), p3(9,6).

A: Step1: Bezier curve :

Q: The velocity components

A: ANSWER: Think about the stream (u, v) = (−y, x). This is a straightforward strong body pivot in the…

Q: Q4: Design SPWM inverter with sinusoidal output voltage Vdc = 311 V, R = 8.8 0, output power Po =…

A: ANSWER:-

Q: Q1. Given the hazard rate function () = 2 × 10-5, Determine R(t) and f(t) at t= 500 h.

A:

Q: Given the hazard rate function λ(t) = 2 × 10ˉ⁵t, Determine R(t) and f(t) at t= 500 h.

A: Hazard measures the conditional probability of a failure given the system is currently working.  The…

Q: 7. The initial heat distribution over a steel plate is given by the function: u(x, y) = 80…

A:

Q: D. Single Phase Circuit Consider the circuit in Figure 2 - 1 Rídr Lfdr ZL Figure 2 -1 Given that Ra…

A:

Q: A single-station machine has a production rate of 1.1 part per minute and a process variance of 4…

A: According to the Question below the Solution:

Q: For the ideal diode, the voltage across the load R₁ is given by [vs if vs > 0 VL 10 if vs ≤ 0…

A: The solution is given below for the above given question:

Q: Determine the sizing of the two gates (x, and y) that will minimize the propagation delay? Let…

A: According to the information given:- We have to find the correct option to satisfy the mention…

Q: When two resistors having resistances R1 ohms and R2 ohms are connected in parallel, their combined…

A: Given:Two resistance, R1 and R2 are connected in parallel.

Q: according to chebsyhevs theorem 95% = +or - 2 standard deviation 97% = +or - 3 standard deviation…

A: 68% percent of data falls within one standard deviation, 95% percent with two standard deviation,…

Q: 2. Describe the functions of the following parts in the power supply Transformer: Bridge rectifier…

A: Power supply: A power supply is an electrical system that provides electrical power to a load. A…

Q: Solve the following max flow problem using Ford-Fulkerson method

A:

Power System

A power system is a network that distributes the electric power produced by the generating plants to the loads using the distribution network. The network is mostly an alternating current (AC) network. The power system mainly consists of generators, loads, transformers, transmission networks, and switchgear (protection equipment).