Using Fig. 4-1, Draw a conclusion about the comfort of mixed group of men and women in typical seasonal clotthing, with sedentary activity for the following cases: (a) Summer, Operative temperature 24 °C, wb 18 °C. It is OComfortable OToo warm OToo Dry (b) Winter, Operative temperature 24 °C, wb 18 °C. It is OToo warm OComfortable OToo Dry (c) Summer, Operative temperature 23 °C, dp 10 °C. It is OComfortable OToo warm OToo Dry (d) Winter, Operative temperature 22 °C, dp 1 °C. It is OToo Dry OComfortable OToo warm wa ma 15 55 of 30 st 68°F (20°C) 70 80 25 Operative temperature 20 50% 36% 79°F (26°C) 40.015 30 C 0.010 0.005 Joo 90 F Pumidity ratio Figure 4-1 Acceptable ranges of operative temperature and humidity for people in typical sum mer and winter clothing during light and primarily sedentary activity (5 1.2 met) (Reprinted by permission from ASHRAE Standard 55-1992)

Using Fig. 4-1, Draw a conclusion about the comfort of mixed group of men and women in typical seasonal clotthing, with sedentary activity for the following cases: (a) Summer, Operative temperature 24 °C, wb 18 °C. It is OComfortable OToo warm OToo Dry (b) Winter, Operative temperature 24 °C, wb 18 °C. It is OToo warm OComfortable OToo Dry (c) Summer, Operative temperature 23 °C, dp 10 °C. It is OComfortable OToo warm OToo Dry (d) Winter, Operative temperature 22 °C, dp 1 °C. It is OToo Dry OComfortable OToo warm wa ma 15 55 of 30 st 68°F (20°C) 70 80 25 Operative temperature 20 50% 36% 79°F (26°C) 40.015 30 C 0.010 0.005 Joo 90 F Pumidity ratio Figure 4-1 Acceptable ranges of operative temperature and humidity for people in typical sum mer and winter clothing during light and primarily sedentary activity (5 1.2 met) (Reprinted by permission from ASHRAE Standard 55-1992)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An automotive company has employed you as a manufacture engineer to start a new unit. You are assigned with the production of the crank shaft piston assembly as shown in FIGURE Q1a. As an engineer responsible for producing the components shown in FIGURE Q1b, you have been asked to prepare a report with following details. Select the appropriate materials for the components shown in FIGURE Q1b.Propose the manufacturing processes that can be used to manufacture each of the components Crankshaft, power gears shown in FIGURE Q1b(I). Discuss the selection of manufacturing process with reference to desired properties for connecting rod application. Recommend appropriate surface treatment methods for these parts as required by their application.
Multiple choice questions, please help thank you!! 1. The chemical potential (μ) of smaller size clusters is bigger than that of bigger size clusters because of (a) their small size (b) the fewer number of atoms in them (c) surface area is smaller (d) their surface is more curved 2. Which of these characteristics would you associate with SEM: A surface imaging tool Maintained under vacuum Provides imaging and compositional data Uses a scanned electron beam All of the above 3. Secondary electrons (SE) are best described as Low energy electrons from the sample surface High energy electrons from the sample surface Low energy primary beam electrons High energy primary beam electrons 4. Atomic force microscopy (AFM) is the most widely used form of scanning probe microscopes for the characterization of nanomaterials since it require: (a) electrically conductive and optically transparent samples (b) neither electrically conductive nor optically transparent samples (c) electrically…
kinetics of particles-relative motion report
In what types of settings do biomechanists typically work?
Hi can you please help me at this point with C and D here?
Problem- Cargo ships can cause a lot of air pollution.Solution- to use nuclear powered ships since they hold a lot of energy and can travel for long distances. How it will work is that it will need a nuclear reactor at the bottom of the boat to heat up the water and then turn it to electricity to power the boat. The boat will be made out of graphene which is a tough material to avoid any leaks in the boat. It will also contain many control rods because nuclear power is so powerful that it can create to much energy to handle. With control rods, you can slow down this process and keep it in a controlled manner. Since cargo ships are already is the ocean, there will be no need for any extra materials to make it work. -Do you think this will work? Why/Why not? -What do you think is wrong with it/ How can this be improved? Please send this to someone else I need to record 50 responses for a science project. Thank you!
Question 03: Discuss with the help of an examplehow is a flywheel able to store energy. Also, compare solid and hollow flywheel, which one will be more effective and why?
Provide and illustration to what is asked.
Please help me, please, I want to solve all the questions, without quoting and without plagiarism, I want the solution in MS Word, I do not want handwriting...
I need a KPI for The project consists of two parts The first is glasses that monitor objects around them, and alert the person when an object is within the specified distanceThe second part is a glove that senses the heat from a distance. When the temperature reaches above the permissible limit, the person is alerted by means of a vibration motor.
In the area of Mechanical Engineering, how well do you know Pro/Engineer software and the applications it can make? Identify three CAD applications and write down their names.
Please I want Mechanical and Physical properties of Human Femur Bone to Make a FEA in Ansys workbench. Thanks