Using C (NOT C++,C#) I need help in coding this practice problem without the use of Strings and Arrays.The problem is attached below Write a program that will compute and display the sum of the powers of x from thefirst power to the nth power, where x and n are nonnegative integers given by theuser.if x = 3 and n = 4, then compute 3' + 3? + 3³ + 3ª = 120;thus display 120if x = 2 and n= 5, then compute 2' + 2² + 2° + 2* +2° = 62;thus display 62ex.ex.

Answered: Using C (NOT C++,C#) I need help in…

Engineering

Computer Science

Using C (NOT C++,C#) I need help in coding this practice problem without the use of String

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

1. Write a program that asks the user to enter n and then it computes the value of the sum: 12 + 22+32 + +n? = Ei? ... check" whenn = 200, the answer shou; ld be 2686700 2. The total resistance of n resistors in parallel is: 1 = R Suppose we have a network of two resistors with the values 400 Q and 200 . Then our equation would be: 1 1 1 R 400 * 200 and the total resistance of our two-resistor network is 133.3 Q. Write a program to compute the total resistance for any number of parallel resistors.
Write a program that reads an integer and displays all its smallest factors, also known as prime factors. For example, if the input integer is 120, the output should be as follows: 2, 2, 2, 3, 5
Write a program that calculates the equivalent resistance of a circuit. n electrical resistors with resistance values R1, R2,.., Rn are said to be connected in parallel if the same voltage is applied across each. Their equivalent resistance Reg is related to the values R1, R2, ..., Rn by: 1 1 1 1 + +...+ R R R, R. "eq Write a program that prompts the user to enter the resistance of n resistors. The user should be prompted continuously by using a while loop until a zero or negative value is entered (the program should count the number of resistors n entered by the user and store the values in an array). Use another separate loop to print the resistance values entered by the user and the equivalent resistance Reg. Test your program with R1= 1 kn, R2= 2 kn, R3= 4 kQ and R4= 8 kQ.
Write a program that asks the user to enter two positive integers, the height and length of a parallelogram and prints a parallelogram of that size with stars to the screen. For example, if the height were 3 and the length were 6, the following would be printed: ****** ****** ****** or if the height was 4 and the length was 2, the following would be printed: ** ** ** **
Write a program that prompts the user to input any digit then swap the position of the first and the last digit. Next, the user will be prompt to select what arithmetic operation he/she want to employ on the first and last digit based on the following choices: 1. Sum of their square 2. Product of their square root 3. Square of their product The output will display the result of the arithmetic operation followed by the digit with a swapped position of “first” and “last” digit. Then finally display the equivalent uppercase alphabet for the first digit and lowercase alphabet for the last digit respectively after swapping. Note: 1. If the last digit of the inputted digit from the user is zero, it must display that there is no equivalent alphabet for that digit. 2. If the user chooses arithmetic operation No.2, format the output to three decimal places TEST CASES: If a user inputs a digit and choose arithmetic operation No.1: Input any number: 97834 Select an arithmetic operation…
Write a program that will determine how many of a set of 10 numbers are even and how many are odd. a. Read in one number at a time. b. Compute and display the number of even integers and the number of odd integers. Hint: You can use the modulus operator (%) to determine if each integer is even or od. Your output should look like this: Enter integer: 2 Enter integer: 4 Enter integer: 3 Enter integer: 5 Enter integer: 6 Enter integer: 4 Enter integer: 77 Enter integer: 5 Enter integer: 89 Enter integer: 45 There are even numbers in the list 6 odd numbers in the list 4 There are >>>
Write a program that takes an integer as input (e.g. 3456) and outputs the number withthe order of digits reversed. For example, input: 3456; output: 6543.
Write a program that reads a four-digit integer, such as 2014, and then displays it, one digit per line in reverse order, like so: 4 1 0 2 Your prompt should tell the user to enter a four-digit integer. You can then assume that the user follows directions. (Hint: Use the division andm remainder operators.)
Write a program that inputs one five-digit number, separates the number into its individual digits and prints the digits separated from one another by three spaces each. [Hint: Use combinations of integer division and the remainder operation.] For example, if the user types in 42139 (no spaces), the program should print. Here is a sample run (blue user input): Enter a number : 42139 4 2 1 3 9
Write a program that calculates the surface area of a hexagonal prism (figure below) which is given by the following formula: A = 6 ah+3√√3 a² Your program should take input, do the appropriate calculation and display output. Paste your code at the space provided below. You can test your code using the following cases: Input I Output I Ia (Base edge) | h (Height) | A (Surface Area) | I 6 10 13 | 3 | 15 | 5 | 295.06 I 1419.62 | 136.77 I
Write a program that reads integers between 1 and 100 and counts the occurrences of each. Assume the input ends with 0. Write a program that reads integers between 1 and 100 and counts the occurrences of each. Assume the input ends with 0. Here is a sample run of the program: Enter integers from 1-100 (input 0 value to end inputs): 2 5 6 5 4 3 23 43 2 02 occurred 2 times3 occurred 1 time4 occurred 1 time5 occurred 2 times6 occurred 1 time23 occurred 1 time43 occurred 1 time
Write a program that prompts the user to input two POSITIVE numbers — a dividend (numerator) and a divisor (denominator). Your program should then divide the numerator by the denominator, and display the quotient followed by the remainder.