Using any Geometric Methods only: (Double Integration, Conjugate Beam, Area Moment) Determine the deflection (mm) of the beam at point B. Round off your final answer in 2 decimal places P kN w kN/m A C X1 X2 EI

Using any Geometric Methods only: (Double Integration, Conjugate Beam, Area Moment) Determine the deflection (mm) of the beam at point B. Round off your final answer in 2 decimal places P kN w kN/m A C X1 X2 EI

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. By the m oment-are a me thod find the slope and de flectio n at the free end A of the can tile ver beam AB. E = 30,000k/in and I = 200 in . Refer to the figure below. A l decim a ls must be in c lu ded, do not round o ff answers. A ll fig ures must be included and drawn straight. curves may be done freehand. Sum m arize your answers as shown be lo w. Required Va lu es Answer B A L1 L2 k/ft ft ft 0.690 6
16cm. 34.8cm = 1.0 SGcone = 0.9 Which is the more stable pesiton? IS
A beam is supported and loaded as shown. In the section of the beam between 'A' and 'B', the equation for the resisting bending moment was determined as: Mr = -6.2x²+50x. Determine the magnitude of maximum resisting bending moment (Mcmax) in the section. Note: Do NOT include units in your answer Answer: AY Fun
The hollow square cross section shown has a wall thickness, T, of 10.9 mm. Determine the second moment of area of the cross section. Note: Give your answer in mm4 Note: Do NOT include units in your answer lo0 nm Answer: evious page Next page ://learnonline.gmit.ie/mad/quiz/attempt.php?attempt=5462898 cmid 425173&page=.. 16°C Mostiy clody ASUS VivoBook esc
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a = 2.8 m, b = 5.6 m, c = 3.8 m, P = 20 kN, w = 45 kN/m, and Q-10 kN. A P B W b C X What is the maximum bending moment on the beam? Answer in kN-m rounded-off to 2 decimal places When entering your answers, use the bending moment sign convention. I
QUESTION 7 A loaded, simply supported beam and its cross-section are shown in the figures below. 5 kN/m 20 mm: 150 mm 20 mm 150 mm 20 mm- 6m 250 mm (a) (b) Calculate the moment of inertia of the section. O 30.1 x 10-7 m4 O 301 x 107 m4 O 301 x 10-6 m4 O None of these O 30.1 x 10-8 m4 QUESTION 8 In Problem 7 (above), what is the maximum bending stress in the beam. O 4.45 MPa O None of these O 1.45 MPa O 12.7 MPa O 14.0 MPa Save All Click Save and Submit to save and submit. Click Save All Answers to save all answers.
The bending moment diagram and cross-section for a beam are shown below. Use the elastic flexural formula ox = -Mzy/l, to determine the required strength of the beam to resist the compressive stresses. Circle the correct answer for the compressive strength in ksi: 2.3, 2.5, 27.5, 30, 37.7 Show your work below. Bending Moment Diagram Beam Cross-Section 4" +50 2' (K-Fe) 2" 2" - 40 2"
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=4.0 ft, b-9.0 ft. c=4.0 ft, d=3.0ft, w=8 kips/ft and P = 66 kips. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. B B ÎÎÎÎÎÎ Answers: Ay=i b d For this loading, calculate the reaction forces Ay and Ey acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) W C b C C D E kips, Ey = i E X Ey kips.
Application of Influence Line: Draw for the influence line of the deflection at the free end of the cantilever beam 15ft long and solve for the corresponding deflection when subject to live loads of 2Kips/ft and 5Kips. The modulus of elasticity and moment of inertia are 29000ksi and 500 in^4, respectively. From the influence line drawn, express the deflection in inches, and round off the answer to 2 decimal places only.
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=4.0 ft, b=8.0 ft, c=4.0 ft, d=3.0 ft, w = 6.5 kips/ft and P = 45 kips. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. a B a W B W C b d For this loading, calculate the reaction forces Ay and Ey acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) b C C P C D P Ľ E d E ·x Ey
Haw-3 The compressiv Stresf (r)of a rectangular beam sectionis given by the fakmula: 6 M bh where Mis bending moment (24 x1 N-mm Pi axiat ferce (6x1o° N) , b is widthof section (30o mm) and h is height of Section (600 mm),if the errok in measuring (M)is +3-6 x lo° N-mmekkak in measuring (P) ir +18x1 x lo N anderror in measuring each (6) and h) 9 mmyuse khe tatat derivative to find the tatal is
Please do not round off in all computations and box all final answers Conduct the following using either Double Integration Method, Moment Area Method, or Conjugate Beam Method Let El be constant. Given that from Point A, x = 8.12 m. What is the value of El(y)? Given that from Point A, x = 5.59 m. What is the value of El (y')? Given that from Point A, x = 4.92 m. What is the value of El(y)? Given that from Point A, x = 9.37 m. What is the value of El (y')? 61 KN 2.35 m 37 KN/m 30 KN/m 2.45 m A B 4.70 m 5.58 m