Using a forked rod, a 0.6-kg smooth peg P is forced tomove along the vertical slotted path r= (0.5 0) m, whereO is in radians. The angular position of the arm is0-() rad where t is in seconds. The peg is inDetermine the magnihide of the force of the rod on the peg at the instant t2sExpress your nnswer to three significant figures and include the appropriate units.contact with only one edge of the rod and slot at anyinstant. (Figure 1)HAF=ValueTnitsSubmitPrevious Answers Requent AnawerX Incorrect; Try Again; 5 attempts remainingFigure1 of 1Part BDetermine the magnitude of the normal force of the slot on the peg.Express your answer to three significant figures and include the appropriate units.r= (0.50) mN. ValueUnitsSubmitPrevious Answers Reguest Answer

Both normal force and force can be calculated by taking equilibrium along the axis. TO begin with,…

Answered: Using a forked rod, a 0.6-kg smooth peg…

Similar questions

Computation M t = An electric grinder is switched on at t = 0, accelerates uniformly for 17 s to its operating angular speed of 34 rad/s. The wheel then turns at constant angular speed for 34 s and is switched off, slowing uniformly at 9.3 rad/s² until it stops. From the time it is switched off, how long does the grinder take to stop turning? S QL Record your numerical answer below, assuming three significant figures. Remember to include a "-" as necessary.
This is third time that I post it all time the given answers was wrong and was chat gpt or ai answer that I have no need. Needs Complete solution with 100 % accuracy don't use chat gpt or ai plz i definitely upvote you for quality solution.
In the figure below, wheel A of radius A = 14 cm is coupled by belt B to wheel C of radius c 20 cm. The angular speed of wheel A is increased from rest at a constant rate of 1.6 rad/s². Find the time needed for wheel C to reach an angular speed of 150 rev/min, assuming the belt does not slip. S B C TG
Plz use g = 9.8 m/s2 to find if needed
Macmillan l A motorized wheel is spinning with a rotational velocity of wo = 1.81 rad/s. At t = 0s, the operator switches the wheel to a higher speed setting. The rotational velocity of the wheel at all subsequent times is given by w (t) = woarctan (c + b1²) where c = 1.5574 and b = 6.09 s-². At what time tamax is the rotational acceleration at a maximum? tamax = What is the maximum tangential acceleration a, of a point on the wheel a distance R = 1.29 m from its center? a₁ = What is the magnitude of the total acceleration of this point? a = ms m/s² m/s²
he diameters of the main rotor and tail rotor of a single-engine helicopter are 7.56 m and 1.06 m, respectively. The respective rotational speeds are 447 rev/min and 4,150 rev/min. Calculate the speeds of the tips of both rotors. main rotor m/s tail rotor m/s Compare these speeds with the speed of sound, 343 m/s. vmain rotor = vsound vtail rotor = vsound
Refer to the picture below.
Starting from rest, a 10.8cm diameter compact disk takes 7.96s to reach its operating rotational speed of 1920.0 rpm (revolutions per minute). Assume that the angular acceleration is constant. The disk's moment of inertia is 3.88E-5kg.m². How much torque is applied to the disk? Submit Answer Tries 0/10 How many revolutions does it make before reaching full speed? (Do not enter a unit.) Submit Answer Tries 0/10
A wheel is turning at 55 rad/s, and is slowing due to friction at a rate of -1.7 rad/s^2. a.) how long will the wheel turn before coming to rest?____ s (2 significant figures-round to the ones place) b.) how far will the wheel turn before coming to rest? ____radians (2 significant figures- round to the tens place)
The spool has a mass of 70 kg and a radius of gyration of KG 0.3 m. (Figure 1) Show Transcribed Text α = = 250 mm Show Transcribed Text HA Templates Value If the coefficients of static and kinetic friction at A are μs = 0.2 and μ = 0.15, respectively, determine the angular acceleration of the spool if P = 60 N. Express your answer to three significant figures and include the appropriate units. A Units 400 mm ? P
The 47-kg flywheel has a radius of gyration of ko = 300 mm about its center of mass. (Figure 1) Figure Part A W = If it is subjected to a torque of M = (90¹/2) N m, where is in radians, determine its angular velocity when it has rotated 3 revolutions, starting from rest. Express your answer to three significant figures and include the appropriate units. μÃ Value Submit Request Answer www. ? M = (9 0¹/2) N.m Units 1 of 1
Needs Complete typed solution with 100 % accuracy.