**M7.1 Six Rules for Constructing Shear and Moment Diagrams****Rule 3:**The slope of the shear diagram at any location is equal to the distributed load value (both magnitude and sign) at that location.**Diagram:**- A beam is shown with two supports; a roller support at the left and a pin support at the right.- There is a point load of 40.0 kN acting downward at a distance of 5m from the left support.- An evenly distributed load of 8.0 kN/m spans 10m from the point load to the right support.- Reaction forces are shown: 53.3 kN upward at the left support and 66.7 kN upward at the right support.**Interactive Section - Try One:**Use the slope of the shear diagram to determine the x-location where V = 0.(Pay special attention to the sign of the distributed load w. If the arrows point down, w is negative. If the arrows point up, w is positive.)- **Options**: A, B, C, D- **Input box** for V = 0 @ x = [ ]Buttons: “check me”, “1st try”, “2nd try”, “3rd try”Ensure to follow the above rule to identify the point where shear V is zero on the diagram.

Answered: Image /qna-images/answer/b7e7145e-64d4-48e3-91c2-d4c5e37a7fdf.jpg

Use the slope of the shear diagram to determine the x location where V = 0. (Pay special attention to the sign of the distributed load w. If the arrows point down, w is negative. If the arrows point up, w is positive.) V = 0 @ x =

Use the slope of the shear diagram to determine the x location where V = 0. (Pay special attention to the sign of the distributed load w. If the arrows point down, w is negative. If the arrows point up, w is positive.) V = 0 @ x =

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 3: Water issues from a hole in a large tank, as shown in the attached figure.Assuming frictionless flow, find L.
Assign the values of shear force and bending moment to the image bar as a function of the x coordinate.q=20kN/mF=14kNM=12kNmL1=1.2mL2=1.4mL3=1.3mL4=1.5m Maximum value of bending torque Mmax = ???Maximum position of bending moment x = ??? Use units (kN,m), Do not round the invoices in the intermediate stages, but only the final answer!
6
At a given 7 locations/sections (0,1,2,3,4,5,6) on a beam of uniform I-section, the beam is subjected to a shear force of 100 kN. Plot a curve to show the variation of shear stress across the section and hence determine the ratio of the maximum shear stress to the mean shear stress given as;
Draw the axial,shear and moment diagram for the given frame. Final answer must be rounded to nearest 3 decimal.
The beam AB in the figure supports a load which varies from an intensity of 50 KN per linear meter to 200 KN per meter. 8.2 Determine the location of the resultant load from point A. 200 KN/m 50 KN/m B 6 m
If the shear force is 50 kN, calculate the shear load per metre length at the top of the flangeof the T-section. [Start your calculations by setting the origin on the bottom of the cross- section].
Needs Complete typed solution with 100 % accuracy.
A cross-section of a beam is shown in Figure Q2. If the shear force in this section is V determine the value and the location of the maximum shear stress in the section. In Figure Q2, a = 68 mm and the origin of the coordinate system is at centroid of the cross section. y= A Z= a I₂ = S = AY mm; Figure Q2 Answer The vertical coordinate (y-coordinate; the y-axis serves as the axis of symmetry of the cross- section.) and horizontal coordinate (z-coordinate) of the location where the maximum shear stress occurs in the section are mm; O 4a Tmax= The vertical distance from the location where the maximum shear stress occurs in the section to the bottom side (AB) of the cross section can be calculated as Distance = mm B Second moment of area The second moment of area employed in the equation to calculate maximum shear stress can be calculated as Shear stress a (units : mm¹ ) First moment of area The first moment of area employed in the equation to calculate maximum shear stress can be…
Plot the Shear and Bending moment diagrams for the following. Use Singularity Functions to Solve the problem y 400 lbf Hinge | A B₁ AC R₂ R₁ 4 in 4 in 2 in 40 lbf/in 10 in D R3 X