Use the completed front and side views to create the top view The image shows technical drawings of two parts that appear to fit together.**Left Part:**- The overall length is 450 mm.- The height is 188 mm.- A 60° chamfer is on the right side.- The chamfered section runs 95 mm from the right end and has a vertical cut of 55 mm from the top.**Right Part:**- The overall width is 250 mm.- The inverted "T" shape at the top has a width of 62 mm and a height of 31 mm on both sides.- The center section is symmetrical with two slanted lines meeting at the center to form a triangular shape inside.- Dashed lines indicate the symmetry and connection points, aligning with the chamfered sections in the left part.This diagram is likely used to demonstrate how the two parts interlock, showing precise measurements for manufacturing or assembly.

Answered: Use the completed front and side views…

Engineering

Mechanical Engineering

Use the completed front and side views to create the top view

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Section view 1- The front and top views of an object are shown below. Freehand sketch the full section view of the front view. The cutting plane should pass through the centers of the holes in top view. Hatch the full sections view by hand. Indicate the location and the direction of the cutting plane and label the section view. Place the section view below the front view 11
FOR THE FOLLOWING FIGURES ISOMETRIC VIEW IS NEEDED Sketch theisometric view using the below following (top front nd side) orthographic view Note : use autocad 2017 version to sketch the following , no hand drawing Thank you
Pleaseeee
Kindly explain the process.
Construct a view that will show both lines in true length. Note: Properly label your ARP's, TL's, and PV's. HRP FRP
Below are the front and side views of the objects. Use these views to create the top view.
I need the answer quickly
Even if a sectional view is available, all hidden lines should be placed on the appropriate views. True? A. Yes, always B. No, it does not matter C. No; ok to leave hidden lines out for clarity
hand written plz Answer the following questions using the information provided in this unit. Know and Understand 1. True or False? The primary purpose of section views is to help feature exterior detail without using hidden lines. For the next three terms, match the three types of lines to the three descriptions. Answers are used only once. 2. Cutting-plane line 3. Section line 4. Short break line A. Not exclusive to section views, but needed for broken- out sections. B. Drawn thick in a view adjacent to the section view. C. Drawn thin, and usually continuous, but sometimes dashed. 5. Of the following, which is not a type of section view featured in this unit? A. Full B. Half C. Quarter D. Offset 6. True or False? The preferred dividing line between the two halves of a half-section view is the visible line. 7. An object with a number of odd features, such as spokes or holes, often has a(n) section so the odd features can be rotated around the axis into a vertical cutting plane,…
Use creo parametric 4.0 and Sketch the necessary and partial views, including auxiliary and sectional views. (can replace by cropped views too). Section side view Auxiliary view Top front side view Note : no hand drawings Use creo parametric 4.0 drawing If don't have skip ,don't reject ,urgent needed
DRAW A TOP VIEW, AND AN AUXILIARY VIEW THAT SHOWS THE TRUE SHAPE OF THE ANGLED SURFACE ON THE FRONT VIEW. H F FIP SCALE: 5.3
I have three parts that need to be answered pertaining to the print provided below. Most of the sections on this print are full sections. What other method of sectioning is used? (Multiple Choice)A: OffsetB: HalfC: RevolvedD: Broken out On this print, there is a stem and knob assembly at an angle to the main view. If an auxiliary view were used to show the round knob as a true circle, could it be projected of off the view? (Multiple Choice)A: No, it would need to be projected from a top viewB: Yes, it should be projected from the front view Why does this drawing only have nine dimensions and those are all in parentheses? (Multiple Choice)A: It is an assembly drawing and the dimensions show distances for reference purposes onlyB: The final dimensions have not yet been determinedC: The model is parametric and the dimensions can change at any timeD: They are all 'basic' dimensions