Use Simulink, you can set the symbol rate as 1 kHz. a) Plot the spectrums of the BFSK, 4FSK, 8FSK, 16FSK system at E_b/N_0=12 dB. Compare the theoretical bandwidth with the observed MFSK spectrums. Note: Simulink has MFSK/MQAM/MPSK baseband equivalent Modulator/Demodulator rather than bandpass. Hence, you can treat the center frequency 0 Hz as the carrier frequency. b) For BFSK, 4FSK, 8FSK and 16FSK, vary E_b/N_0 and obtain the P_b vs E_b/N_0 (in dB) curves. (For P_b you need to show both simulated BER and theoretical BER on top of each other). Create a transmission bandwidth, data rate, and BER table for the considered modulations, and comment on your results.

Use Simulink, you can set the symbol rate as 1 kHz. a) Plot the spectrums of the BFSK, 4FSK, 8FSK, 16FSK system at E_b/N_0=12 dB. Compare the theoretical bandwidth with the observed MFSK spectrums. Note: Simulink has MFSK/MQAM/MPSK baseband equivalent Modulator/Demodulator rather than bandpass. Hence, you can treat the center frequency 0 Hz as the carrier frequency. b) For BFSK, 4FSK, 8FSK and 16FSK, vary E_b/N_0 and obtain the P_b vs E_b/N_0 (in dB) curves. (For P_b you need to show both simulated BER and theoretical BER on top of each other). Create a transmission bandwidth, data rate, and BER table for the considered modulations, and comment on your results.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q4) Draw the IC's diagram of the circuit shown below using the required 74 series DODA B D LL
( Back EENG250 Midterm - S... Time left 00... Not yet answered Question 3 Marked out of 7.00 Using voltage division, find VAB. 11 Q 18 Q 12 Q VAB V2 12 V 12 Q 70 Select one: a. VAB=7.741. b. VAB=3.6V. c. None Of them d. VAB=12 e. VAB=4.8 V.
Answer a, b, c and d...
G5 C(s) G1 G2 G3 G4 R(s) – G6 Ho H,
Answer the following
D5 15 12 ID6 Calculate: a. I2 b. ID6 V R2 D6 20V 3.3k2 C. I15
Find the value of the load resistance for maximum power transfer
Answer the following problems in a short/long bond paper size. Round off your answer up to 2 decimals, if applicable. Show your complete solution and box your final answer. You may not copy the problem. uatmeters are properly coneete to eaSU r draw y a baranged attertove the cORnections IS Cur -ee the pf of the foad at .at TGi at an officioACV-of 9U%. Find w Tnserted to eesure a OWby tgePmcied blanced deltasnnecedloau S connected across a balapced3entrase, 120 V, 60 M om TwO wattmete nroveCOnnected to Reasurei OWdrawn W. ine- a of 4. A balanced, 3-phase, 132 kV line supplies power to a balanced load that draws 70.7 MVA at 0.707 pf lagging. A delta-connected capacitor bank is connected in parallel to correct the pf to unity. Find the reactance per phase of the capacitor bank.
Q5:- Find the Z parameter of the following network. I1 R1=100 12 R2=400 R3=300
parallel to series. write your solution pls.
Complex numbers are crucial in ultrasound imaging to represent both the amplitude and phase of the sound waves used to create images of internal tissues and organs. Express the following complex numbers in polar form (reje with -π < 0 ≤ π). Z₁ = (1 + 2j)/(1 - 2j) Z₂ = (1 + j)ejπ/6 -) Demonstrate that the derivative of a sinusoidal function yields the same result when calculated using complex exponentials. Consider the waveform y(t)=sin(200лt + л/4) representing the signal driving an ultrasound transducer. First, calculate the time derivative of this waveform (dy/dt). Then, express y(t) in terms of complex exponentials and take the derivative. Did you obtain the same result?
Node2: Node1 www..