Answered: IV. Solve the following problems…

Math

Calculus

IV. Solve the following problems completely. 3 1. Use local linear approximation to estimate √√(3. 95)³

Algebra and Trigonometry (MindTap Course List)

4th Edition

ISBN:9781305071742

Author:James Stewart, Lothar Redlin, Saleem Watson

Publisher:James Stewart, Lothar Redlin, Saleem Watson

Chapter2: Functions

Section2.4: Average Rate Of Change Of A Function

Problem 4.2E: bThe average rate of change of the linear function f(x)=3x+5 between any two points is ________.

See similar textbooks

Similar questions

Find the unknown value. 27. y varies jointly with x and the cube root of 2. If when x=2 and z=27,y=12, find y if x=5 and z=8.
Compute the following problems. Express the answers to 1 decimal place. Use: T=LFN Seven brass plates 9.00 inches wide and 21.00 inches long are machined with amilling cutter along the length of the plates. The entire top face of each plate ismilled. The width of each cut allowing for overlap is 212 inches. Using a feed of0.020 inch per revolution and 525 rpm, determine the total cutting time.
Compute the following problems. Express the answers to 1 decimal place. Use: T=LFN Fifteen 3.20-millimeter diameter holes each 57.15 millimeters deep are drilled inan aluminum workpiece. The high-speed steel drill runs at 9200 r/min with a feedof 0.05 millimeter per revolution. Determine the total cutting time.
Compute the following problems. Express the answers to the nearer whole number. Use C=3.1416DN12 or DN12 for customary units and C=3.1416DN1000 or DN1000 for metric units. A finishing cut is taken on a brass workpiece using a 100-millimeter diameter carbon steel milling cutter. What is the cutting speed when the cutter is run at 86 r/min?
Compute the following problems. Express the answers to 1 decimal place. Use: T=LFN Cast iron, 312 inches in diameter, is turned in a lathe at 270 rpm. Each length of cut is inches and five cuts are required. A carbide tool is fed into the work at 0.015 inch per revolution. What is the total cutting time?
Compute the following problems. Express the answers to the nearer whole number. Use C=3.1416DN12 or DN12 for customary units and C=3.1416DN1000 or DN1000 for metric units. What is the surface speed of a 16-inch diameter surface grinder wheel running at1194 rpm?
Compute the following problems. Express the answers to the nearest whole number. Use N=12C3.1416D or 12CD for customary units and N=1000C3.1416D or 1000CD for metric units. An annealed cast iron housing is drilled with a cutting speed of 20 meters per minute using a 22-millimeter diameter carbon steel drill. Find the revolutions per minute.
Compute the following problems. Express the answers to the nearest whole number. Use N=12C3.1416D or 12CD for customary units and N=1000C3.1416D or 1000CD for metric units. Determine the revolutions per minute of an aluminum alloy rod 1.250 inches in diameter with a cutting speed of 550 feet per minute.
If a coffee filter is dropped, its velocity after t seconds is given by v(t)=4(10.0003t) feet per second. What is the terminal velocity, and how long does it take the filter to reach 99 of terminal velocity? Use a table increment of 0.1 and given your answer to the nearest tenth of a second.
When a certain drug is taken orally, the concentration of the drug in the patient's bloodstream After t minutes is given by C(t)=0.06t0.0002t2 where 0t240 and concentration is measured in mg/L .When is the maximum serum concentration reached, and what is that maximum concentration?
Compute the following problems. Express the answers to the nearer whole number. Use C=3.1416DN12 or DN12 for customary units and C=3.1416DN1000 or DN1000 for metric units. A 312 inch diameter high-speed steel cutter, running at 55 rpm, is used to rough mill a steel casting. What is the Cutting speed?
bThe average rate of change of the linear function f(x)=3x+5 between any two points is ________.