Use FEM to calculate the temperature at nodes 2 and 3, as well as the heat at nodes 1 and 4. area

Q: 12. Depicted below is the side-view sketch of a breakfast bar/shelf that I built several years ago.…

A:

Q: i want a displacement and stress equations from the global matrix that you can find it from the code…

A: First, we define the given parameters. The node coordinates, element connectivity, material…

Q: Deep sea pipelines are used to transport oil and gas across large distances, at depths greater than…

A: height of the pipe, h = 2000 mrmin = 400 mdiameter of the pie, d = 24 inch = 240.0254 = 0.6096 mt=…

Q: A 4.8 m long from fixed point, 0.5 m wide and assumed a thickness of 30 mm throughout a springboard…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: 3. During tug of war, the bicep muscle generated 4k N force that was perpendicular to the forearm…

A:

Q: Points for stress vs strain (in image) Assume the compressive concrete strength (f’c) is 3,000…

A:

Q: 3 3 Problem A: Analysis of light aircraft rudder udder of an aircraft is usually found at the tail…

A:

Q: Unit: BTU HL = Heat loss (BTU)= Hv x hours If loss for one day, H = 24 hrs If we are talking about a…

A: Heat loss (HL) per day through a single building element =  AreaArea (A)Resistance (R)×∆T×24 hours…

Q: A marine engine cylinder has a compression ratio (r) of 9.5, a clearance volume of 650 cm3 and a…

A: Given, Compression ratio-9.5 VC clearance volume-650cm3 L-67.5cm

Q: Draw the kinematic diagrams of the following mechanisms and compute the number of Degrees of Freedom…

A: It is asked to draw a kinematic diagram

Q: A pressurized vessel (closed ends) with 500 bar, its dimensions are L=1m, d = 25 Cm, D = 32 Cm, o, =…

A: Internal pressure (P) = 500 bar = 50,000,000 PaDiameter of the vessel (D) = 32 cm = 0.32 mInside…

Q: Point "P", as shown below, is located between nodes 2 and 3 of a quadratic 1D bar element. Workout…

A: Given data: location of node 1, x1 = 10.8 mm location of node 2, x3 = 34.6 mm location of point P in…

Q: Use the graphical method to break F into components parallel to bars AB and BC. If the component…

A: According to the given data  FAB =7kN a = 300mm b = 75mm c = 100mm  we need to find Force in the…

Q: Question #5 (Similar to Question #4, You solved, I have attached the question #4) Design a question…

A: Design a question to calculate the heating load for the building you selected indoor Environment…

Q: Don't Use Chat GPT Will Upvote And Give Handwritten Solution Please

A: Step 1: Step 2:

Q: In the below structure what is the number of redundancy? If the structure is unstable key in -100.…

A: Given: Let us consider the given figure, Lets determine the number of redundancy.

Q: How are you solving the equations in step 4 to get the values for Tad, ab, ac? Especially when each…

A: We have following equations

Q: ead intrustions on example and help anwser it please and th

A: Jsolid Cylinder =πd432 DAC = 0.9 JAC =π 0.9432=0.064412467

Q: 4. This diagram shows the front-end of a machine that has a bucket at the tip. The total weight of…

A: solution Step 1 -:                Draw FBD of bucket and analyze tanθ =0.32.5θ=6.843°sin θ =0.12cos…

Automation in manufacturing processes

The term automation refers to the technique through which the creation of an apparatus takes place using an automatic process or a system. Let us try to understand this with an example.