Use a 1 mH inductor to design a low-pass, RL, pas- sive filter with a cutoff frequency of 5 kHz. a) Specify the value of the resistor. b) A load having a resistance of 68 N is connected across the output terminals of the filter. What is the corner, or cutoff, frequency of the loaded fil- ter in hertz?

Use a 1 mH inductor to design a low-pass, RL, pas- sive filter with a cutoff frequency of 5 kHz. a) Specify the value of the resistor. b) A load having a resistance of 68 N is connected across the output terminals of the filter. What is the corner, or cutoff, frequency of the loaded fil- ter in hertz?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Discuss how the frequency response of the resulting GLP FIR filter designed using the windowing method is related to the “ideal” filter and why the windowing operation does not destroy the GLP property.
We apply a 5-V-rms 20-kHz sinusoid to the input of a first-order RC lowpass filter, and the output voltage in steady state is 0.5 V rms. Predict the steady-state rms output voltage after the frequency of the input signal is raised to 150 kHz and the amplitude remains constant.
a). Consider a fifth-order low pass Chebyshev I filter with a pass band of 1 KHz and a pass band ripple of 1 dB. What is the attenuation of this filter in dB at f=1 KHz and f=2 KHz. b) Determine the order and the poles of a type I low pass chebyshev filter that has a 2-dB ripple in the pass band, a cut-off frequency Op=1500n , a stop band frequency of 2500n, and an attenuation of 40dB or more for 2>
Design a basic wide-band, RC band stop filter with a lower cut-off frequency of 200HZ and a higher cut-off frequency of 900HZ. Vor Band Stap Flepone -3dB Pas Band Paes Band Freguency fie) Low Pas Hgh Pa Response Response Frequancy (rie) Figure 1: Band Stop Filter Characteristics Assuming a capacitor, C value for both filter sections (CLP. CHP) of 0.2uF, calculate the values of the two resistors, RLP and RHP using the formula: 1. From the Low pass filter formula, Find RLP: 1. fi 2. From the High pass filter formula, Find RHP: 1 2nRypCHP 3. Calculate the center frequency (fc) and Bandwidth (BW): a. fc = Vfi x fu %3D b. BW = fr - f.
Don't copy from other platform
There is a system that works with a sampling rate of 48 kpsp and requires a bandpass filter that lets the spectral components pass between the fa=12kHz and fb=16kHz sequences. If you are using a 32-tap FIR filter. What is the value of the central frequency, f0, in Hz of the band that passes the filter? And what is the outline of the frequency response for the filter passes bands?
Draw frequency response curve of a bandpass filter whose end frequencies are 0.1 MHz and 0.4 MHz respectively. Consider peak amplitude as 1. Use your own scale and necessary values.
H5.
A single pole high pass filter has a frequency-selective circuitwith R= 22 kohms and C = 0.0015 uF. What is the critical frequency?. Can you deterrnine the bandwidth from the available information? What is the roll-off rate? Explain how Butterworth, Chebyshev, and Bessel responses differ. Is the filter circuit as shown below approximately optimized for a Butterworth response? What is the roll off rate? What is the critical frequency? Adjust the componentvalues 1.2 k, 1 k, and2k resistors to obtain an approximate Butterworth response. 22 k 22 k 0.012 uF ol012 uF iVin 0.012 ala12 uF 아012 uF iVout 22 k 500 22 330 470 22 k 1k .2 k 2k
Please answer in short like it definitely don't reject in shorts please..
An inductive proximity sensor is used to detect the presence of car in traffic lights. The output circuit of the sensor produces a sinusoidal signal at 20 KHz. This signal is usually mixed with a random high and low frequency noise around the signal. Design a suitable cascaded bandpass filter to remove the unwanted signals given that the passband region is not more than 4 KHz. Also, sketch the magnitude and phase responses of the filter.
Find the normalized frequency that corresponds to a DT filter cut-off of pi/4. What normalized frequency corresponds a cut-off of 500Hz if the sampling frequency is 11,025 Hz?