(USCS UNITS) A GO/NO GO PLUG GAUGE WILL BE DESIGNED TO INSPECT A 2.000 +/- 0.002mm DIAMETER HOLE. A WEAR ALLOWANCE OF 5% OF THE TOTAL TOLERANCE BAND IS APPLIED TO THE GO SIDE OF THE GAUGE. DETERMINE THE NOMINAL SIZES OF THE GO GAUGE. ROUND YOUR ANSWER TO THE NEAREST TENTH OF A THOUSANDTH OF AN INCH

Q: 1. For the following part sizes and geometric tolerances, determine the appropriate geometric…

A: Givenϕ 2.062-0.0050.00⊥-Perppendular Toleranceϕ⊥=0.002

Q: What type of geometric tolerances have no datum features? Profile Tolerances All Tolerances O…

A: Geometrical Tolerancing: The tolerances in any system which allows tolerances to be applied…

Q: Specify a cylindricity tolerance of .0004 for the largest cylindrical surface on the part in the…

A:

Q: If the main scale reading(mm) and vernier scale reading (division) are 11 and 15 respectively for a…

A: main scale reading = (MSR) = 11 mm vernier scale reading (VSR) = 15 mm no of division = 20

Q: Q13) For the following micrometer: a- What is the part diameter?

A: 13

Q: Which position tolerance is shown in below’s technical drawing? Explain the meaning (that is the…

A: Which position tolerance is shown in below technical drawing?Explain the meaning (that is the…

Q: Tolerance note is given by: .XX ± .01 cm and .XXX ± .001 cm. What is the tolerance for a feature…

A: Given:- Tolerance note .XX ±.0.1.XXX ± 0.001To find:- Tolerance for a feature

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: I require a gap of .03 min and .06 max between the 2.50 dim and the B dim (at the bottom). I apply a…

A:

Q: In the following figure, add the tolerance zone and limits of size for both parts.

A:

Q: QI) A) Fill the following blanks 1- Misalignment of measuring instrument is called 2- Applying a…

A: 1. Misalignment of measuring instrument is called Abbe's Error 2. Applying a number of known…

Q: Using the 10% rule–of–thumb for determining gagemaker’s tolerance for a plug gage, determinethe GO…

A: Given data: Calculate the maximum hole dimension as follows: Calculate the minimum hole dimension…

Q: Select the right reading of the ?Micrometer Screw Gauge

A: we need to find reading in the micrometer.

Q: I need help with question number 15 that is pertaining to the print provided.

A: 15.The unidirectional system is used here for the dimension placing. The unidirectional system is…

Q: s a caliper use to measure inside diameters widths of slots and the like [a)micrometer (b)outside…

A: To determine the correct option.

Q: In pressure gages, the difference between the actual value and error value (+/-) is called…

A:

Q: The measurement 0.000 004 3 m, expressed correctly using scientific notation, is

A: Scientific notation  0.0000043 m = 4.3 *10^-6 m

Q: f the metric micrometer to a precision

A: 5.332

Q: Use the prefix multipliers to express cach measurement without any exponents. 22 x 10-15s

A: Given: The time is t=22×10-15 s. The unit conversion factor to convert Second into Femtosecond is, 1…

Q: High precision in angular measurements can be made using a sine bar. For using a 300 mm sine bar to…

A:

Q: 1. For the following part sizes and geometric tolerances, determine the appropriate geometric…

A: (A) Pin, φ2.062-0.005+0.000  tolerance =upper limit - lower limit tolerance = 0.000-(-0.005)…

Q: 13. What type of geometric tolerance has no datum features? 14. A theoretically exact dimension is…

A: As per Bartleby guidelines, this is a multipart question and we will answer the first three…

Q: Identify which is the GO plug and which is the NO GO.   Please explain

A: As per ISO standard design of go-no go gauge will follow as below.for solution refer below images.

Q: You are given a set slip gauge containing 46 pieces of 2mm base (M46/2). Show how you would build…

A:

Q: The uniform beam has a mass of 41 kg per meter of length. Determine the reactions at the supports. A…

A:

Q: Use prefix multipliers to express each measurement without any exponents. 87.9 x 10-L

A: Given: The expression is 87.9×10-7 The scientific notification for the expression is, 87.9×10-7…

Q: For the following part sizes and geometric tolerances, determine the appropriate geometric tolerance…

A: A.    Geometric tolerance = 0.005 + 0.007                                     = 0.007…

Q: Using the Metric Full Scale Below, what is the red dimension below to the nearest Millimeter? .01…

A: Steps

Q: Using the Engineering Scale 1" = 20', what is the red dimension below to the nearest foot? 20 20 0 1…

A:

Q: What type of form tolerance is shown in this figure?   Flatness Straightness Cylindricity…

A: Given data : Figure

Q: If the pin in the drawing below is produced at Ø.498, what is its total positional tolerance? C…

A: Given data as per the question Pin diameter =0.498

Q: dimension the distance between the holes

A: Bilateral tolerance B = 1.625T = 0.006Bilateral tolerance means that the dimension can vary in both…

Q: II. Comprehensive questions. 1. Explain the meaning of the following annotations, the tolerance…

A: For solution refer below images.

Q: Refer to the Ø.750 dimension. A) Where is the tolerance specified ?…

A: 1—position 2 – the shape of the tolerance zone

Q: I need help solving problem numbers 4--15.

A: Hello, thanks for the question. Since we only answer up to 3 sub-parts, we’ll answer the first 3.…

Q: 31. (USCS units) A GO/NO-GO plug gage will be designed to inspect a 2.000 0.002 mm diameter hole. A…

A: Given data as per questionDimension of object to be inspected =2.000±0.002mmWear allowance…

Q: Using the diagram, determine the minimum clearance, in inches. DIA A 0.000 0 -0001 6" BASIC…

A:

Q: how do you write this in a feature control frame? "The cross-sectional shape of this feature must be…

A: The feature control frame is required to describe the condition and tolerances of the geometric…

Q: The least count of a dial test indicator is 0.01 mm which is a direct measurement device with 100…

A: It is required to evaluate given statement

Limits, Fits, and Tolerances

The maximum or minimum allowable sizes within which the size of component lies are known as limits. The limits are classified into two types: