unit = symunit; rho_water = 1000 *unit.kg / (unit.m^3); rho_air = 1.3 *unit.kg / (unit.m^3); g = 9.81 unit.m / (unit.s)^2; Question 1 A paint sprayer uses air flow to spray paint, as described in figure below. Calculate the minimum flow rate in segment A so that the paint can be sprayed. The B reduction has dg = 2. 5mm and paint has similar density to water. Po 50 mm |20 mm 120 mm Po B.

unit = symunit; rho_water = 1000 unit.kg / (unit.m^3); rho_air = 1.3 unit.kg / (unit.m^3); g = 9.81 unit.m / (unit.s)^2; Question 1 A paint sprayer uses air flow to spray paint, as described in figure below. Calculate the minimum flow rate in segment A so that the paint can be sprayed. The B reduction has dg = 2. 5mm and paint has similar density to water. Po 50 mm |20 mm 120 mm Po B.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

6. When the path of individual particles does not cross or intersect, the flow is said to be A. Turbulent C. Uniform B. Laminar D. Non-uniform 7. A Reynolds Number, Re = 1 x 10°, indicates that the flow is B. Steady A. Transitional C. Laminar D. Turbulent 8. Cavitation in fluid mechanics refers to A. The separation of the air flow behind a wing. B. The oscillations of a plate due to turbulent fluctuations. C. The liquid to gaseous phase transition of a fluid due to low pressure. D. The condensation of vapor into liquid due to high pressure. 9. Machines that involve the flow of fluid through rotors that remove or add energy to the fluid. A. Positive displacement machines B. Slider crank machines C. Reciprocating Machines D. Turbomachines 10-THe difference between the pressure at the pump suction and the vapor pressure of the liquid at the given temperature expressed as pressure head. A. Vapor Head B. Pressure Head C. Net Positive Suction Head D. Velocity Head
State whether the statement is true or false, and if it is false, correct it. (Don't explain. Don't draw. Just write the corrected statement) A. Airfoil camber is the maximum distance between the mean camber line and the chord line, measured perpendicular to the mean camber line. B. For cambered airfoil, the lift is not equal to zero at zero angle of attack. C. Critical Mach number of an airfoil is the first supersonic free stream mach number. D. Induced drag is the drag due to high angle of attack E. Propeller blades are twisted to increase its structural strength.
i%TA lI. In. 1 1:19 و أمتحان يومي.pdf Fox flow mate 28 Lis Sind EL. 60M puup Power 150 Mm El. 30M Scanned by CamScanner
BASED ON ASHRAE STANDARD 62.2, CALCULATE THE FRESH AIR INTAKE TO THE AIR HANDLING UNIT (AHU) THAT SERVES LECTURE HALL THAT CAN ACCOMMODATE 150 STUDENTS, DIMENSIONING 30M X 65M X 3M (H).
23.The fuel gage for a gasoline (sp. gr. = 0.68) tank in a car reads proportional to its bottom gage. If the tank is 30 cm deep an accidentally contaminated with 2 cm of water, how many centimeters of gasoline does the tank actually contain when the gage erroneously reads "FULL"? Air Vent Vent Gasolne, s- 0.68 30 cm Gasoline, s= 0.68 2 cm TWater "Ful "Full
Q11: Find the SPECIFIC GRAVITY of the OIL Gol in the Tank shown in Figure 10, if the pressure at point D is Po = 21 (KN/m2). The values of a = 1 (m), b = 0.4 (m), c = 0.4 (m) and d = 0.5 (m). Air Air W.L A surface of oil W.L Yw B W.L Oil Goil=0.9 yw Figure 10
56. A pump is operating in recirculation mode. At time zero, we close the bypass valve and simultaneously open the isolation valve to fill the initially drained sup- ply line. Use the data to find the time it takes to fill the supply line. Data: = 200 GPM, Lsupply Line = 1200 ft, Dsupply Line = 3 in. [Ans.: ~ 132 s]. pump Bypass Isolation Valve Bypass| Isolation Valve Valve Valve
4. Testing, adjusting, and balancing is a prerequisite before starting-up of an air-conditioning system used for public areas. To perform this, it is needed to measure the flow rate available within the system. What would you prefer to use in such a measurement? A) Pitot- static Tube B) Thermal (Hot-Wire and Hot-Film) Anemometers C) PIV D) Pitot Tube
Q. Blood flow. An artery of diameter 1.0 cm divides completely into capillaries, each of diameter 20 microns. There are a large number of capillaries, N, such that the net cross sectional area for these capillaries is equal to the cross sectional area of the artery. What is AP:/APa, the ratio of the pressure change per unit length along one of the capillaries (AP) to that of the pressure change per unit length along the artery (APa)? O2.5 x105 O1.0 O4.0 x10-6 5.0 x102 12 x108 O 6.2 x1010 Page 10 of 1
A brand of toothpaste is made using a mixture of white and red paste. During the manufacturing process, both pastes are pumped through a pipe, with the red paste lying in the centre of the pipe, as shown in Figure Q2. The pipe has an internal radius, R₂, and the segment of red paste has a radius R₁. The flow is found to follow the Poiseuille equation, i.e. u(r) = I - 1 dp 4µ dx (R2² - r²) Where u is the viscosity of the paste and is the pressure gradient. The total flow of toothpaste through the pipe is Qtot, and the flowrate of the red paste is Qred. dx The toothpaste has a density of p = 1200 kg/m³, and a viscosity of 0.03 Pa.s. The pipe has a radius R₂ = 5 cm and a length L = 2 m. a) Find an expression for the flowrate of the red toothpaste. You answer should be in dp terms of μ, R₁, R₂, P) H, b) The flow in the pipe becomes turbulent when the Reynolds number reaches 2000 (where Re is calculated using the mean velocity across the pipe). What is the maximum pressure drop along the…
a) Assuming the effluent from the pulp and paper plant has a daily discharge of 15 m3/s, calculate the daily loading values for TSS and BOD5. (Remember: Loading (kg/day) = Q (m3/s) x concentration (mg/L)) **don’t forget your unit conversions and show your work if you can Assume a BOD5 concentration of 10 mg/L, and a TSS of 20 mg/L.
Describe the volume flow rate is the volume of fluid flowing through a cross section per unit time.