-Unit-Load Method: For the given beam below, answer the questions. E = 29,000 ksi and Problem I = 53.8 in: |8 k B A D 5 ft 10 ft 5 ft Show the virtual load on the answer sheet to calculate the slope angle at point C using the unit- (a) load method (mark the magnitude of the load). (b) | Determine the slope angle at point C, 0c, using the unit-load method.

Q: Draw the frontside and topview the Shape Shown

A: Asked: To draw the front, side and top view of the given shape.   The required engineering id drawn…

Q: Determine degree of external indeterminacy

A: Given data : Number of external support reaction (R)=3+1+1=5

Q: Hi can you give me analysis about space truss?

A: This question is related to the Truss analysis from Structural analysis from Civil Engineering. This…

Q: Good structural design is more related to correct natural sense than to sets of

A:

Q: 3 cm 7 cm 5 cm 5 cM Detenmine the Folloeing %3D

A: Calculation of area and moment of inertia

Q: Many objects, such as train tracks and road joints, are specifically designed to allow extra space…

A: Brief concept- Train tracks and road joints- Train tracks are the path for the trains over which…

Q: Determine external and total indeterminacy

A: Given data : Number of external support reaction (R)=2+1=3Number of member (m)=3Number of joint…

Q: Locate the centroid of the composite area below

A:

Q: Find the vertical and horizontal line detect segmentation

A: Detecting vertical and horizontal lines in an image is a common task in image processing and…

Q: The elastic centroidal distance from the bottom is.. * 98 mm 212 mm 200.40 mm 89.50 mm

A: GIVEN DATA DEPTH OF WEB, DW=300 mm WIDTH OF WEB, BW=12 mm DEPTH OF FLANGE, DF=240 mm WIDTH OF…

Q: What is the degree of kinematic indeterminacy of the truss as shown in figure?

A:

Q: CAD is used to

A: You need to familiarize yourself with a range of civil engineering programme, if you are interested…

Q: Use the unit load method to calculate the vertical displacements at the quarter and mid-span points…

A: The given figure is shown below:

Q: The T shaped cross section shown below is reinforced with 4 of 32 mm bars with fc'= 20.7 MPa and fy…

A:

Q: A composite beam is fabricated by bolting two 2.5- in.-wide by 11-in.-deep timber planks to the…

A: Es = 30800 ksi Et = 1660 ksi Determine a. Maximum bending stress in timber and steel if P = 3.5…

Q: Discuss Designing for Shear

A: Introduction : Shear stresses in design normally operate in planes perpendicular to a member's…

Q: How did u calculate minor and major stress

A: Minor and major stress

Q: Draw shear force Diagram 600 lb 4000 lb ft |C D 10 ft + 5 ft 5 ft-

A: Support reaction : ∑MB=0RA×20-600×10+4000=0RA=100 lb∑FY=0RA+RB-600=0100 +RB-600=0RB=500 lb

Q: Appendix 1 shows a structural drawing of the first floor of a random building. The labels "C"…

A: Structural drawing for the first floor of the building C- Columns D1–4 is a 200 UB 29.8,3C–D is a…

Q: The required number of diameter bar is 32mm, why you use 36? and can you pls add show drawing or…

A:

Q: DETERMIME Fou つ こ I =

A:

Q: Height in inches is an example of a(n) _________ scale

A: There are 2 types of scales  1) Ratio scale  2) Interval scale   1) Ratio scale: it contains all…

Q: determine the degree of indeterminacy.

A: * Hinge support: - It is defined as the support which resists horizontal and vertical reaction but…

Q: Determine external indeterminacy

A: Given:- A frame is given with fixed support To determine:- The external indeterminacy

Q: Draw and name the different Types of Trusses

A: Truss is a structure commonly used in case of bridge spans. Members carry load because of the…

Q: Give me right answer Draw a flowchart on how to analyze a flexural member with rolled W-shape bent…

A: The flow chart for analysis of flexure member with rolled W-shape bent is shown below: (The flow…

Q: Problem 1 Find the x-coordinate measured from the y-axis of the centroid for the section shown. 30-…

A:

Q: Define Earth pressure loads

A: Pressure is defined as force acting per unit area of the body.

Q: lap splicing

A: A lap splice is when two pieces of rebar overlap to form a continuous reinforcement. This helps…

Q: A. sketch the joint and the members that can be define by the following STAAD editor code? joint…

A: Asked: To draw the joints and members using the given STAAD editor code.   Given: joint coordinates…

Q: Consider the beam X-section shown. Assume 1 inch clear spacing between two layers of bars. As the…

A: 1 inch clear spacing spacing between two layers of bars. Beam width = 12 inch Layer = 2 No of bars =…

Q: the parts of the construction plan of a bridge and Horizontal structure.

A: BRIDGE:- Bridge is a structure that carries a road or railway across a river, valley, road or…

Q: Should one way slab be used for Steel Deck if the slab is a Square

A: Yes. Generally that is true.   The beauty of steel structures lie behind the short construction…

Q: Discuss rigid methods

A: Rigid method is used for designing mat foundation in which it is assumed that mat foundation is…

Q: A. sketch the joint and the members that can be define by the following STAAD editor code? joint…

A: Asked: To sketch the joints and members of the structure that is defined by the given STAAD editor…