Under steady-state de conditions, find i and v in the circuit in e Fig. 6.71.2 mHel+5 mA30 kN20 k.6 µF

Answered: Image /qna-images/answer/098feb32-70b6-4efe-aeaf-27abac50f059.jpg

Answered: Under steady-state de conditions, find…

Engineering

Electrical Engineering

Under steady-state de conditions, find i and v in the circuit in U Fig. 6.71. 2 mH ll 5 mA (4 30 k2 20 k2 6 µF +

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Battery Air Fuel A fuel gauge uses a capacitor to determine the height of the fuel in a tank. The effective dielectric constant kchanges from a value of 1 when the tank is empty, to a value of 7, when the tank is full. The appropriate electronic circuitry can determine the effective dielectric constant of the combined air and fuel between the capacitor plates. The dimension of the fuel tank is width w = 19 cm, length L = 12 cm and breadth d = 18 cm. The height of the fuel between the plates is h = 7 cm. A battery with e.m.f of 12 v is connected across the plates. For gasoline, dielectric constant Kig You can ignore any fringing effects. a) Calculate the effective dielectric constant of the fuel tank. (Hint: Consider two different capacitors connected in parallel) b) How much energy is stored in the fuel tank when it is full up by gasoline? c) What is the capacitance, when 0.75 fraction of the fuel tank is filled by the gasoline? d) What is the capacitance, when the fuel tank is totally…
Show solution
A capacitor with a capacitance of 32 microfarads is discharged through a resistance of 53 kilo-ohms. How many milliseconds does it take for the voltage to drop to 1/e of its initial value. Here "e" is the base of natural logarithms, about 2.718 .
A circuit is constructed with a resistor, two inductors, one capacitor, one battery and a switch as shown. The value of the resistance is R1 = 231 0. The values for L, R, the inductances are: L1 = 307 mH and L2 = 114 mH. The capacitance is C = 190 uF and the battery voltage is V = 12 V. The positive terminal of the battery is indicated with a + sign. L2 4) What is Q(t1), the charge on the capacitor at time t = t = 4.83 ms. Qt1) is defined to be positive if V(a) - V(b) is positive. uC Submit 5) What is t2, the first time after the switch is opened that the energy stored in the capacitor is a maximum? ms| Submit 6) What is the total energy stored in the inductors plus the capacitor at time t = t2? Submit
None
-2•t mA (tis in 6.32 In the circuit below, the source current function is ig = 4.0.e second in this equation), and the voltage across each capacitor is equal to zero at t = 0. The capacitors = 21 UF , C2 = 13 UF , and C3 = 14 UF. Determine the v2 (in V) when t = 1.3 s. Please pay attention: the numbers may change since they are randomized. Your answer must include 1 place after the decimal point. %3D %3D %3D C3 + is V2 C2 10 Ω Your Answer: Answer
A 3.0 MΩ resistor and a 1.0 μF capacitor are connected in series with an ideal battery that has an emf E = 5.0 V. After 1.0 s after the initial connection is made, find the rate at which(a) the charge on the capacitor is increasing (inC/s),(b) energy is being stored in the capacitor (inJ/s),(c) thermal energy is appearing in the resistor (inJ/s), and (d) energy is being delivered by the battery (inJ/s).
A 20-uF capacitor has a voltage of 5V across it at t=0. If a constant current of 30mA flows through the capacitor, how long will it take for the capacitor to charge up to 180 uC?
Three capacitors, with capacitances of C1 = 2.0 μF, C2 = 3.0 μF , and C3 = 6.0 μF, respectively, are connected in parallel. A 500-V potential difference is applied across the combination. Determine the voltage across each capacitor and the charge on each capacitor.
At t= 0, a 2.3 uF capacitance is pre-charged to an unknown voltage V. The capacitance is in parallel with a 4 k2 resistance. For t>0 the capacitor is disconnected from the charging source and allowed to discharge into the resistor. At t = 2 ms, the voltage across the capacitance is 10 V. Calculate the value of V (V).
For the circuit of Figure 2. Assuming that the capacitor voltage and inductor current are equal to zero at t = 0. a) Determine the expression for all the branch currents and capacitor voltage v(t) b) Obtain the plots of the branch currents and v(t) by creating a MATLAB model in Simulink. Verify the plots by using a MATLAB program
find all graphs and show calculations