У 180 pies- 10 ton 35° 20° 8 ton 8 ton Fig. P2.21

Q: l force onto the inner bottom rim of the lid. Given that the Dol at point A and a 20-lb force is…

A: The force exerted on the handle is .To find-The force exerted on the rim.

Q: Q2: determine the value of F Which effect with other two forces as shown in Fig. if the Resultant of…

A: Givenresultant forces=80N

Q: what is the direction and magnitude of the resultant?

A: Analyze the FBD of the given system.

Q: The y-component of the force F which a person exerts on the handle of the box wrench is known to be…

A: The angles from given figure are - cosθ=513,  sinθ=1213 The y-component of force is given by-…

Q: Determine the force (written as a vector) which BC exerts on member AB (a) if the 820-N load is…

A:

Q: Plot the magnitude of the resultant R of the three forces as a function of 8 for 0 ≤ 0≤ 360°. After…

A: Given data: F1 = 73 NF2 = 116 NF3 = 81 Nϕ = 54°ψ = 18°We have to find the maximum and minimum value…

Q: Fig. 2 F = 300 N = 250 N 309 60° 2 m 3 m 4 m B F= 500 N Fig. 3

A:

Q: the vertical post is secured by three cables. the cables are pre-tensioned so that the resultant of…

A: There are two types of forces that are acting on a circular surface. One type of force is Radial…

Q: The force P = 2 kips is applied to point A, and is supported by cable AB, cable AC, and bar OA. The…

A:

Q: Two rods and one cable are attached to the supports at O. If two of the forces are as shown,…

A:

Q: Two rods and one cable are attached to the supports at O. If two of the forces are as shown,…

A:

Q: die is being used to cut threads on a rod. If 30-lb forces are applied as shown, determine the…

A:

Q: Q1: Determine the magnitude of the force on the pin at A for the boom shown in Fig. 1. Neglect the…

A:

Q: The combined action of the three forces on the base at O may be obtained by establishing their…

A:

Q: Four parallel forces act on the plate as shown. For the force system shown, find the equivalent…

A:

Q: 3- Determine the force T and C 3 kN 20 16 kN 40 8 kN

A: In horizontal direction    Tcos40+8+Csin20-16=00.766T+0.342C=8         -1

Q: Practice Problem 3.4.9: Determine the resultant of the force 300 lb system acting on the…

A: Given data: The force in positive z direction is Fz = 120 lb. The force in negative z direction is…

Q: What is the magnitude of the resultant force caused by the three forces below? Assume that a, = 50°,…

A: Vector is a physical quantity that has magnitude and direction both. Scalar is a physical quantity…

Q: Easy Problem: Determine P and Q so that the their resultant force R are equivalent to a single 2000…

A:

Q: Q2: determine the value of F Which effect with other two forces as shown in Fig. if the Resultant of…

A:

Q: oolting forces act on the e the resultant force, and spe n the plate. lb. FA = 300 lb, FE

A: Given   FA=300lbFB=200lbFC=500lb

Q: ie is being used to cut threads on a rod. If 18-Ib forces are applied as shown, determine the…

A: Given:P=18 lbr=7.5 inx=0.5 in

Q: Solve for the resultant of the forces applied on the object. Determine whether the object will slide…

A:

Q: Q2: determine the value of F Which effect with other two forces as shown in Fig. if the Resultant of…

A:

Q: Two rods and one cable are attached to the supports at O. If two of the forces are as shown,…

A:

Q: PROBLEM 3.49 3.50 Determine the magnitude and location of the resultant for the load system shown.…

A: Find the magnitude and location of resultant force.

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A: Consider the diagram shown below for the given system.

Q: 400 lb 6 pies - A' B 4 pies C 4 pies E D' 8 pies

A:

Q: Easy Problem: Determine P and Q so that the their resultant force R are equivalent to a single 2000…

A:

Q: The combined action of the three forces on the base at O may be obtained by establishing their…

A: Given data: F1=350 lb F2=660 lb F3=520 lb a=5.4 ft b=2.9 ft c=4.0 ft θ=50o

Q: Two rods and one cable are attached to the supports at O. If two of the forces are as shown,…

A:

Q: Two rods and one cable are attached to the supports at O. If two of the forces are as shown,…

A: GivenR=Ry=1170lb

Q: 1. Determine the forces P and Q at point K and M respectively to produce a couple of 350 kN-m…

A:

Q: Determine graphically the forces FAB and FAC

A:

Q: Rod AD is supported by two cables as shown. The tension in cable AB is 500 N and in cable AC is…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.