ty +x 20 m An incline of height 20 m and 0 = 12° has an object of mass m=1.5 kg sliding down on it. The coefficient of kinetic friction is µ= 0.30; the magnitude of the air resistance is kv, k being 0.07 kg/s and v as the velocity. A. Draw the inertia-force diagram of the system. B. Model the problem using a FOLDE. Express the equation in standard form. Take note of the indicated reference axes in the figure above. C. Determine the general solution, velocity as a function of time.

ty +x 20 m An incline of height 20 m and 0 = 12° has an object of mass m=1.5 kg sliding down on it. The coefficient of kinetic friction is µ= 0.30; the magnitude of the air resistance is kv, k being 0.07 kg/s and v as the velocity. A. Draw the inertia-force diagram of the system. B. Model the problem using a FOLDE. Express the equation in standard form. Take note of the indicated reference axes in the figure above. C. Determine the general solution, velocity as a function of time.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need answers for problems 1, 2, and 3 pertaining to the print.
how do i draw sectional view of this object.
I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the example shows on problem number 1. Here is the link to the questions I already had answered, could you please rewrite the answer so its properly answered as the example shows (Problem 1)? https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/cadc3f7b-2c2f-4471-842b-5a84bf505857
Statics of Rigid Bodies Note: If you have already answered the problems in this post, kindly ignore it. If not, then answer it. Thank you, Tutor! Content Covered: - Method of Joints Direction: Create two problems based on the topic "Method of Joints" and then solve them with a complete solution. In return, I will give you a good rating. Thank you so much! Note: Please bear in mind to create two problems based on the topic "Method of Joints." Be careful with the calculations in the problem. Kindly double check the solution and answer if there is a deficiency. And also, box the final answer. Thank you so much!
I want to talks about this paragraph very briefly (pen heads)
Question 6 a) The bore of each cylinder in a six-cylinder car engine is 45 mm and the stroke for each piston is 125 mm. calculate the cubic capacity of the engine in cubic centimetres (cm³); and calculate the clearance volume per cylinder for a compression ratio, r, of 8.75. b) The bore of each cylinder in a four-cylinder four-stroke internal combustion engine is 38 mm and the stroke of each piston is 165 mm. During testing, the engine runs at 180 revolutions per minute (rpm) with a pressure-volume indicator diagram showing a mean net area of 3.4 cm² and a diagram length of 1.2 cm. The pressure scale on the indictor diagram is set to 150 kN/m² per cm. Calculate the mean effective pressure (m.e.p) and the indicated power developed by this four-cylinder four-stroke engine. c) Figure Q6c shows a pulley system with a suspended load w of 2000 N. Calculate the following: (i) (ii) (iii) (iv) The effort force (FEffort) necessary to lift and hold a load of 2000 N. The ideal mechanical advantage…
Multiple choice questions, please help thank you!! 1. The chemical potential (μ) of smaller size clusters is bigger than that of bigger size clusters because of (a) their small size (b) the fewer number of atoms in them (c) surface area is smaller (d) their surface is more curved 2. Which of these characteristics would you associate with SEM: A surface imaging tool Maintained under vacuum Provides imaging and compositional data Uses a scanned electron beam All of the above 3. Secondary electrons (SE) are best described as Low energy electrons from the sample surface High energy electrons from the sample surface Low energy primary beam electrons High energy primary beam electrons 4. Atomic force microscopy (AFM) is the most widely used form of scanning probe microscopes for the characterization of nanomaterials since it require: (a) electrically conductive and optically transparent samples (b) neither electrically conductive nor optically transparent samples (c) electrically…
Mechanical Advantage Review Directions: Use the appropriate equation to answer the following questions. All answers should be recorded below or in your engineering design journal. Remember to show all work. 1. A lever has an effort arm that is 8 meters long and the resistance (load) arm that is 5 meters long, how much effort is needed to lift a 200 Newton weight?
Please do the last three questions (2, 3 and 4)! Thank you in advance! A seesaw that weights 45lbs and its 5m long is balanced on the fulcrum in the center. 1- Two children are sitting on opposite sides of each other on the seesaw. One child weights 50lbs and is sitting 0.7m on the left end. Where should the other child sit in order to be balanced on the seesaw if they weigh 42lbs? 2- Now, a third child wants to sit on the seesaw and weighs 30lbs and is sitting 1.25m in front of them and is closer to the fulcrum on the right side. What are the CW and CCW moment of the seesaw now? What is the net moment and direction? 3- Then, a fourth child wants to play on the seesaw and is on the left side of the plank in order to bring the system to equilibrium. How much does the child weigh (Calculate the pounds of force needed in order for rebalance?) 4- Now the fourth child leaves the other three children sitting on the plank. If the three children are sitting in the same potions as they did…
Hello sir, I want to solve in a clear beautiful font that will be a manual line with a pen I know a strange request and don't forget my name and thank you sir, God bless you
I was given this image for the purpose of studying for an upcoming exam. No additional info was given. Any suggestions on how to study for potential questions that could be asked about this image?
It is still saying that is not correct. I have tried this practice problem over and over and that is the only part that it keeps saying is incorrect. the negative and units are correct. I appreciate your help.