Two units of generation maintain 132 kV and 120 kV (line) at the ends of an interconnector of inductive reactance per phase of 40V and with negligible resistance and shunt capacitance. A load of 22 MW is to be transferred from the 132 kV unit to the other end. Calculate the necessary conditions between the two ends, including the power factor of the current transmitted.

Two units of generation maintain 132 kV and 120 kV (line) at the ends of an interconnector of inductive reactance per phase of 40V and with negligible resistance and shunt capacitance. A load of 22 MW is to be transferred from the 132 kV unit to the other end. Calculate the necessary conditions between the two ends, including the power factor of the current transmitted.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Explain the concept of FACTS (Flexible Alternating Current Transmission Systems) devices. How do they enhance the control and stability of power systems? Provide examples of FACTS devices and their applications.
Select the base voltages for one section and calculate the base voltages for the rest of the sections. Remember that the voltages given are line-line. Calculate the current and impedance for all sections of the System. Assume a base complex power of 100 MVA.
A synchronous generator has been synchronized to an infinite grid of 13.8 kV and 60 Hz. The generator prime mover C/C is such that the no-load frequency is 62.5 Hz and the power slope is 1 MW/Hz. The AVR C/C (The reactive power against the terminal voltage C/C) is such that the zero reactive power voltage is 14.6 kV, while the slope is 0.4 MVAR/kV. Calculate: (a) the kVA loading of the generator and its power factor. (b) the settings of the prime mover and AVR such that the generator delivers 3 MW at 0.85 lagging power factor.
No-load operation and short circuit tests were performed on three-phase, 50 Hz 480/220 delta / Y connected transformer. In these testsThe line voltage, line current and three-phase total power have been measured from the high voltage windings and the test results are below.pictures. 100 A DC current when 1.08 V DC voltage from non-transferable software is applied to the low voltage windingshas attracted.Find the single phase equivalent circuit parameters of this transformer.idle test:Voltage: 480V Power:114w current: 0.71Ashort circiut test:V: 10v P: 78w c: 18.3a
There is a three-phase system such that the phase current in the generator, lines and charging phase is the same. The phase voltage in the generator must be 1000 [V] with clockwise sequence. The connected load must be such that the phase current in each load is 10 [A] and its power factor is 0.97 “lagging”. a) Determine phase currents in the generator, lines and phase in the load
Question 3. A three-phase impedance load balanced D a connected load in parallel with a balanced ? connected load made of bonding. D each arm for the load ?D = 6 + 6? and ? each arm for the connected load It is given as ?? = 2 + 2?. ? the connected load ?? = 1? is earthed through the neutral impedance. To this impedance load, the symmetrical component voltages ?0 = 10∠60°, ?1 = 100∠0° and ?2 = Unbalanced phase-to-earth voltages ??, ?? and ?? of 15∠200° volts were applied. a) Draw the zero, positive and negative sequence circuits. b) Find the complex powers imparted to each component circuit.
Two single-phase transformers, having equal turns ratio, in parallel supply a secondary load of 1,000 A at 0.8 pf lagging. For each transformer the secondary emf on open circuit is 3,300 V and their total leakage impedances referred to secondary are (0.10 + j0.20) ohms and (0.05 + j0.040) ohm, respectively. Determine the output current on each transformer.
In a 3-phase Overhead System, each line is suspended by a string of 3 Insulators. The voltage across the top unit and middle unit are 10KV and 11KV respectively. Calculate (i) Ratio of Shunt Capacitance to Self-Capacitance of each insulator and (ii) String Efficiency
A 10 MVA three phase load is to be served by a three phase transformer at aline voltage of 13.8 kV. The supply side voltage(line-line) is 138 kV. Varioussingle phase transformers are available in the warehouse but all havewindings with voltage ratings under 100 kV and current ratings under 250 A.Is it possible to serve the load using only three single phase transformers? Ifso, specify the three phase connections and the low and high voltage ratingsof the single phase transformers.
A three-phase transmission line and a telephone line are supported on the same towers a shown in the figure. The power line carries a 60-Hz balanced current of 200-A per phase . the telephone line is located directly below phase b. assuming balanced three-phase currents in the power line, find the voltage per kilometer induced in the telephone line. 3.6 m 3.6 m Dal Da2 Del De 4 m 11.2 m-
In the system shown in Figure 1, the transformers are connected star-star with both star points grounded and the generator is connected in star with its star points grounded. The per unit impedances of each element on a 40 MVA base are given in Table 1 and the voltage levels are given in Table 2. Z [p.u.] 0 2 tööt Generator 0.01 +j0.08 p.u. L Figure 1: A section of the distribution system Transformer T1 Line V BASE [KV] 0.04 + j 0.03 + j 0.15000000000000002 0.06000000000000000 Generator Table 1: Sequence impedances (p.u. on 40 MVA base) 3 T2 181. Line 3 10 Table 2: Voltage bases (kV) Load 1 Transformer T2 Load Current A load current of 11.316 kA is flowing with a lagging power factor of 90 %. Convert this to a current vector in per-unit. IL = 0.04 + j 0.06000000000000000