Answered: Two traffic signals are attached to the… | bartleby

Related questions

Question

1. Two traffic signals are attached to the 36 ft support
cable at equal intervals as shown. Determine the
equilibrium configuration angles a, ß and y, as well as
the tension in each cable segment
35'
12'
12'
Ans.
B
12'
TAB =
B =
TBc =
100 lb
Y =
Tcp =
200 lb
000

Expert Solution

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

Determine the forces in members BC and CG. The forces are positive if in tension, negative if in compression. A 10 kips Answers: BC= CG= Mi B 11' G Mi 13' 11' C 11 D 5 70° E kips kips
ect loca tecd What would happen to the stick? the Figure A 10m long uniform bar with a 80 W is attac hed by africtionless hinge to weighte of horizontal rope that wall and held by a malces anr le Qof 37° witn the bar. Culculate the distance from the hinge, x, tha t the 10kg tension T in the rope is 25N. Hint: Use g 10 W/kg, sin37°360 and cos 37°: 9. ang should besus peded if the n fo?
A boom with an angle of theta, supports a 1000 lbs load as shown in the figure. Assume that the force exerted by the boom is 3 times the force exerted by the cable that holds it in place, what is the force exerted by Cable A?
Determine the magnitude Pof the vertical force required to lift the wheelbarrow free of the ground at point B. The combined weight of the wheelbarrow and its load is 231 lb with center of gravity at G. 25* 16" Answer: P-1 B 18' 21" lb
The following forces are acting on the bracket below. The bracket has a width w of 2 inches and a height h of 3 inches. The bracket is in equilibrium (not accelerating). Determine F3y knowing F1x-98 lbf and F1y=195 lbf. For this question, what is F3.y in Ibf? Note that the y- direction is pointing up, so if the force is pushing down on the bracket, it has a negative magnitude. 39
Determine the force in member BE of the loaded truss. The force is positive if in tension, negative if in compression. D 5 KN 8 KN 2 KN 2 m 2 m B 2 m A Answer: BE = i E -4 m F kN
D. A - EVEN: A 1.5kN bar AB carries a load F = 65 kN vertical force at A. The bar is supported by a pin at B and the 12.5-mm. diameter cable CD. 4m 3m 3m Find the a. tension in the cable CD in kN. B b. Horizontal reaction at B in kN. 100 mm F c. Vertical reaction at B in kN. d. Tensile stress in the cable in MPa. e. Shearing stress at B in MPa. 85 mm 12.5-mm dia. Detail at B
KPECTED HAS OCCU... Subject ystem S- rchpool.sona- ems.com man Subject Pool tem Department... 6³ 2 [108 W 24,919 Xx :8: F2 3 6. A 150 kg uniform beam is attached to a vertical wall at one end and is supported by a cable at the other end. Calculate the magnitude of the tension in the wire if the angle between the cable and the horizontal is 8 = 46°. X 1832.64 N E 20 F3 $ 4 R HEATRA MAL 2 7 F4 % 5 T F5 ^ 6 tv ♫ MacBook Air F6 Y & 7 44 F7 U M M | L T E 10 * 8 0 30.0⁰ DII F8 ( 9 Beam A DD F9 O O W F10 zoom B P C F11 ISUIH by mi 04 M vauies or roc puffer d + = F12 delete
Determine the force in each member of the loaded truss. The force is positive if in tension, negative if in compression. 31 59 Answers: AB= i BC= AC = i i B 218 kg N Z Z Z N N
Determine the tensile force in each cable
A window shade with a length of 1.50m and a mass of 30.0kg hinges at the wall and is held up by a rope attached to 0.85m from the hinge along the awnings length. the rope is perpendicular to the shade. the shade makes an angle of 60.0 degrees with the wall. a sign hangs from the end of the shaded. a) what is the maximum mass the sign can have if the rope can withstand 300N of force before it breaks? b) what are the horizontal and vertical components of the force of the hinge on the awning?
The system shown consists of cable segments AD, BD, and CD knotted together at D. Force F acts at point D as shown. Determine the magnitude of the tensile forces in pounds in cable segments AD, BD, and CD. Tad- _______________ lb Tbd- _________________ lb Tcd- _________________ lb

SEE MORE QUESTIONS